Bedienungsanleitung Kenwood KDC-309G (Seite 4 von 32) (Englisch)

523241

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English

Notes

• If you experience problems during installation,

consult your Kenwood dealer.

• If the unit fails to operate properly, press the Reset

button. The unit returns to factory settings when

the Reset button is pressed.

• Press the reset button if the disc auto changer fails

to operate correctly. Normal operation should be

restored.

SCAN RDM

REP

OFF

VOL

AUD

SET UP

PTY

DISP

AME

SCRL

• The characters which can be displayed by this

unit are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ;

^ - { } | ~ .

• The illustrations of the display and the panel

appearing in this manual are examples used to

explain more clearly how the controls are used.

Therefore, what appears on the display in the

illustrations may differ from what appears on

the display on the actual equipment, and some

of the illustrations on the display may represent

something impossible in actual operation.

Cleaning the Unit

If the faceplate of this unit is stained, wipe it with a

dry soft cloth such as a silicon cloth.

If the faceplate is stained badly, wipe the stain off

with a cloth moistened with neutral cleaner, then

wipe neutral detergent off.

• Applying spray cleaner directly to the unit may affect its

mechanical parts. Wiping the faceplate with a hard cloth

or using a volatile liquid such as thinner or alcohol may

scratch the surface or erases characters.

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get dirty,

wipe them with a dry, soft cloth.

Before using this unit for the first time

This unit is initially set on the Demonstration mode.

When using this unit for the first time, cancel the

<Demonstration mode Setting> (page 23).

About DAB Tuner control

(KDC-W4531)

Refer to A group on the Instruction manual of DAB

Tuner KTC-9090DAB (optional accessory) for the

control method of DAB Tuner function.

However, the following control methods of the

function for this unit may be differed from the

Instruction manual; therefore, refer to the following

supplemental instruction.

1. Select the preset band for Auto Ensemble

Memory Entry.

2. Press the [AME] button for at least 2 seconds.

Open Auto Ensemble Memory Entry.

After storing in the memory finishes, the

number of the pre-set buttons and the

ensemble label are displayed.

and <Languages to be displayed>

At the operation to press [DISP] button, press [TI]

button.

This function cannot be used.

This Product is not installed by the manufacturer

of a vehicle on the production line, nor by the

professional importer of a vehicle into an EU

Member State.

The marking of products using lasers

(Except for some areas)

CLASS 1

LASER PRODUCT

The label is attached to the chassis/case and says

that the component uses laser beams that have

been classified as Class 1. It means that the unit

is utilizing laser beams that are of a weaker class.

There is no danger of hazardous radiation outside

the unit.

Reset button

B64-2932-00_English.indd 4B64-2932-00_English.indd 4 04.9.30 4:37:02 PM04.9.30 4:37:02 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KDC-309G Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KDC-309G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info