Bedienungsanleitung Kenwood kdc 7021 se (Seite 34 von 38) (Englisch)

168903

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

English

— 34 —

What might seem to be a malfunction in your unit may

just be the result of slight misoperation or miswiring.

Before calling service, first check the following table

for possible problems.

General

? The power does not turn ON.01

✔ The fuse has blown.

☞ After checking for short circuits in the wires, replace the fuse with

one with the same rating.

✔ No ACC position on vehicle ignition.02

☞ Connect the same wire to the ignition as the battery wire.

? If you have selected Standby mode, the power will go OFF

automatically.03

✔ The Power OFF Timer function has been activated.

☞ If you do not want the power to go OFF automatically, cancel the

Power OFF Timer function.

? Nothing happens when the buttons are pressed.04

✔ The computer chip in the unit is not functioning normally.

☞ Press the reset button on the unit (page 4).

? There’s a source you can’t switch.06

✔ There’s no CD inserted.

☞ Set the media you want to listen to. If there’s no media in this

unit, you can't swhich to each source.

✔ The Disc changer isn’t connected.08

☞ Connect the Disc changer. If the Disc changer isn’t connected to

it's input terminal, You can't switch to an external disc source.

? The faceplate does not open or close.09

✔ The faceplate is incorrectly attached.

☞ Reattach the faceplate correctly, See the section on <Removing

the Faceplate>(page 11).

? The memory is erased when the ignition is turned OFF.10

✔ The battery wire has not been connected to the proper terminal.

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

✔ The ignition and battery wire are incorrectly connected.11

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

? The TEL mute function does not work.15

✔ The TEL mute wire is not connected properly.

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

? The TEL mute function turns ON even though the TEL mute wire is

not connected.16

✔ The TEL mute wire is touching a metal part of the car.

☞ Pull the TEL mute wire away from the metal part of the car.

? Even if Loudness is turned ON, high-pitched tone isn't compensated

for. 17

✔ Tuner source is selected.

☞ High-pitched tone isn't compensated for when in Tuner source.

? The Bass center frequency, Bass quality factor, Bass extend, Middle

center frequency, Middle quality factor, and Treble center frequency

can’t be adjusted.19

✔ The <System Q> (page 25) is set OFF.

☞ Set it ON.

? No sound can be heard, or the volume is low.

✔ The fader or balance settings are set all the way to one side.21

☞ Center the fader and balance settings.

✔ The input/output wires or wiring harness are connected incorrectly.22

☞ Reconnect the input/output wires or the wiring harness correctly.

See the section on <Connecting Wires to Terminals>.

✔ The values of Volume offset are low.24

☞ Increase the values of Volume offset. (page 9)

Troubleshooting Guide

KDC-7021SE_U.S 02.11.24 6:58 PM Page 34

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood kdc 7021 se Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info