Bedienungsanleitung Kenwood KDC-BT47SD (Seite 17 von 21) (Englisch)

511175

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

32 English English 33

CONTENTS

Installation/connection

Part list:

A Faceplate ...................................................................(×1)

B Escutcheon ..............................................................(×1)

C Mounting sleeve ...................................................(×1)

D Wiring harness .......................................................(×1)

E Removal tool .......................................................... (×2)

F Microphone (3 m) ................................................ (×1)

Basic procedure

1 Remove the key from the ignition switch,

then disconnect the · terminal of the

car battery.

2 Make proper input and output wire

connections.

\ <Wiring connection> (page 34)

3 Install the unit to your car.

\ <Installing the unit> (page 35)

4 Reconnect the · terminal of the car

battery.

5 Reset the unit. (page 3)

¤Warning



The unit can only be installed in a car with a

12 V DC power supply, negative ground.



If you connect the ignition wire (red) and

the battery wire (yellow) to the car chassis

(ground), you may cause a short circuit,

that in turn may start a fire. Always connect

those wires to the power source running

through the fuse box.



Disconnect the battery’s negative terminal

and make all electrical connections before

installing the unit.



Insulate unconnected wires with vinyl tape

or other similar material. To prevent a short

circuit, do not remove the caps on the ends

of the unconnected wires or the terminals.



Be sure to ground this unit to the car’s

chassis again after mounting.



If the power is not turned ON (“PROTECT”

is displayed), the speaker wire may have a

short-circuit or touched the chassis of the

vehicle and the protection function may

have been activated. Therefore, the speaker

wire should be checked.

¤Caution



If your car’s ignition key switch does not

have an ACC position, connect the ignition

wires to a power source that can be turned

on and off with the ignition key. If you

connect the ignition wires to a constant-

voltage power source, as with battery wires,

the battery may die.



Do not use your own screws. Use only the

screws provided.



Install this unit in the console of your

vehicle. Make sure the faceplate will not hit

the lid of the console (if any) when closing

and opening.



After the installing the unit, check whether

the brake lamps, blinkers, wipers, etc. on the

car are working properly.



Mount the unit so that the mounting angle

is 30° or less.



If the fuse blows, first make sure the wires

are not touching other parts to cause a

short circuit, and then replace the old fuse

with one with a new the same rating.



Connect the speaker wires correctly to the

corresponding terminals. The unit may be

damaged or fail to work if you share the ·

wires or ground them to any metal part in

the car.



When only two speakers are being

connected to the system, connect the

connectors either to both the front output

terminals or to both the rear output

terminals (do not mix front and rear).



Mounting and wiring this product requires

skills and experience. For safety’s sake, leave

this work to professionals.

If you experience problems during

installation, consult your Kenwood dealer.



Reception may become poor if there are

metal objects near the Bluetooth antenna.

Bluetooth antenna unit

PAR

iPod

VOICE

For Good Reception

To assure good reception, note the following:



Communicate with the cell-phone within

the line-of-sight distance of 10 m (30

ft). The communication range becomes

shorter depending on the surrounding

environment. The communication

range also becomes shorter when there

is an obstacle between this unit and

the cell-phone. The above maximum

communication range (10 m) is not always

assured.



A broadcast station or walkie-talkie located

nearby can interfere with communication

due to a too strong signal.

¤ CAUTION

Install this unit in the console of your

vehicle.

Do not touch the metal part of this unit

during and shortly after the use of the

unit. Metal part such as the heat sink and

enclosure become hot.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KDC-BT47SD Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KDC-BT47SD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info