Bedienungsanleitung Kenwood KDC-PSW9527 (Seite 62 von 67) (Englisch)

41269

Zoom out

Zoom in

Vorherige Seite

1/67

Nächste Seite

English

Troubleshooting Guide

What might seem to be a malfunction in your unit

may just be the result of slight misoperation or

miswiring. Before calling service, first check the

following table for possible problems.

General

? The power does not turn ON.

✔ The fuse has blown.

☞ After checking for short circuits in the wires,

replace the fuse with one with the same

rating.

✔ Speaker cable touches on chassis etc.

☞ Wire or insulate the speaker cable properly

and press the reset button.

✔ The Demonstration mode has been selected.

☞ Hold down button [5] and press the Reset

button to release the Demonstration mode.

? There’s a source you can’t switch.

✔ There’s no media inserted.

☞ Set the media you want to listen to. If there’s

no media in this unit, you can’t switch to each

source.

✔ The Disc changer isn’t connected.

☞ Connect the Disc changer. If the Disc changer

isn’t connected to it’s input terminal, You can’t

switch to an external disc source.

? The memory is erased when the ignition is

turned OFF.

✔ The ignition and battery wire are incorrectly

connected.

☞ Connect the wire correctly, referring to the

section on 'Connecting Wires to Terminals'.

? There’s no loudness effect.

✔ The 'System Q' (KDC-W8027) (page 20) is set to

SRS WOW.

☞ Turn it to the other items.

? The TEL mute function does not work.

✔ The TEL mute wire is not connected properly.

☞ Connect the wire correctly, referring to the

section on 'Connecting Wires to Terminals'.

? The TEL mute function turns ON even though the

TEL mute wire is not connected.

✔ The TEL mute wire is touching a metal part of the

car.

☞ Pull the TEL mute wire away from the metal

part of the car.

? Even if Loudness is turned ON, high-pitched tone

isn’t compensated for.

✔ Tuner source is selected.

☞ High-pitched tone isn’t compensated for when

in Tuner source.

✔ The 'System Q' (KDC-W8027) (page 20) is set to

SRS WOW.

☞ Turn it to the other items.

? The Bass center frequency, Bass quality factor,

Bass extend, Middle center frequency, Middle

quality factor, and Treble center frequency can’t

be adjusted.

✔ The 'System Q Setting' (page 50) is set OFF.

☞ Set it ON.

? No sound can be heard, or the volume is low.

✔ The fader or balance settings are set all the way to

one side.

☞ Center the fader and balance settings.

✔ The input/output wires or wiring harness are

connected incorrectly.

☞ Reconnect the input/output wires or the

wiring harness correctly. See the section on

'Connecting Wires to Terminals'.

✔ The values of Volume offset are low.

☞ Turn up the Volume offset, referring to the

section on 'Audio Control' (KDC-W8027) (page

22)/ 'Audio control' (KDC-PSW9527/W9027)

(page 26).

✔ The 'Built-in Amp Mute Setting' (page 50) is ON.

☞ Turn it OFF.

✔ If the PLII is selected by 'Audio Setup (Easy mode)'

(KDC-PSW9527/W9027) (page28) and if the Front

speaker is set to "16 — 7✳10" and the Center

speaker is set to "16 over," the subwoofer does not

sound.

☞ ---

? The sound quality is poor or distorted.

✔ One of the speaker wires is being pinched by a

screw in the car.

☞ Check the speaker wiring.

✔ The speakers are not wired correctly.

☞ Reconnect the speaker wires so that each

output terminal is connected to a different

speaker.

? Subwoofer Output, Subwoofer Low Pass Filter

and Subwoofer setting can’t be done.

✔ The 'Dual Zone System' (page 24) is ON.

☞ Turn it OFF.

? The Touch Sensor Tone doesn’t sound.

✔ The preout jack is being used.

☞ The Touch Sensor Tone can’t be output from

the preout jack.

? Even though Synchronize Clock is ON, the clock

can’t be adjusted.

✔ The received RDS station isn’t sending time data.

☞ Receive another RDS station.

? The Dimmer function doesn’t work.

✔ The Dimmer wire isn’t connected correctly.

☞ Check the Dimmer wire connection.

KDC-PSW9527(E)_U.S _r5 62 03.11.28, 11:01:09 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KDC-PSW9527 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KDC-PSW9527

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info