Bedienungsanleitung Kenwood KDC-W4034AY (Seite 31 von 36) (Englisch)

446145

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Troubleshooting Guide

English

What might seem to be a malfunction in your unit

may just be the result of slight misoperation or

miswiring. Before calling service, first check the

following table for possible problems.

General

? The power does not turn ON.

✔ The fuse has blown.

☞ After checking for short circuits in the wires,

replace the fuse with one with the same

rating.

? There’s a source you can’t switch.

✔ There’s no media inserted.

☞ Set the media you want to listen to. If there’s

no media in this unit, you can’t switch to each

source.

✔ The Disc changer isn’t connected.

☞ Connect the Disc changer. If the Disc changer

isn’t connected to it’s input terminal, You can’t

switch to an external disc source.

? The memory is erased when the ignition is

turned OFF.

✔ The ignition and battery wire are incorrectly

connected.

☞ Connect the wire correctly, referring to the

section on <Connecting Wires to Terminals>.

? The TEL mute function does not work.

✔ The TEL mute wire is not connected properly.

☞ Connect the wire correctly, referring to the

section on <Connecting Wires to Terminals>.

? The TEL mute function turns ON even though the

TEL mute wire is not connected.

✔ The TEL mute wire is touching a metal part of the

car.

☞ Pull the TEL mute wire away from the metal

part of the car.

? Even if Loudness is turned ON, high-pitched tone

isn’t compensated for.

✔ Tuner source is selected.

☞ High-pitched tone isn’t compensated for when

in Tuner source.

? No sound can be heard, or the volume is low.

✔ The fader or balance settings are set all the way to

one side.

☞ Center the fader and balance settings.

✔ The input/output wires or wiring harness are

connected incorrectly.

☞ Reconnect the input/output wires or the

wiring harness correctly. See the section on

<Connecting Wires to Terminals>.

✔ The values of Volume offset are low.

☞ Turn up the Volume offset, referring to the

section on <Audio Setup> (page 9).

? The sound quality is poor or distorted.

✔ One of the speaker wires is being pinched by a

screw in the car.

☞ Check the speaker wiring.

✔ The speakers are not wired correctly.

☞ Reconnect the speaker wires so that each

output terminal is connected to a different

speaker.

? The Touch Sensor Tone doesn’t sound.

✔ The preout jack is being used.

☞ The Touch Sensor Tone can’t be output from

the preout jack.

? Even though Synchronize Clock is ON, the clock

can’t be adjusted.

✔ The received RDS station isn’t sending time data.

☞ Receive another RDS station.

Tuner source

? Radio reception is poor.

✔ The car antenna is not extended.

☞ Pull the antenna out all the way.

✔ The antenna control wire is not connected.

☞ Connect the wire correctly, referring to the

section on <Connecting Wires to Terminals>.

B64-3294-00_English.indd 31B64-3294-00_English.indd 31 05.10.6 0:51:56 PM05.10.6 0:51:56 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KDC-W4034AY Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KDC-W4034AY

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info