Bedienungsanleitung Kenwood KDC-W5541 (Seite 18 von 24) (Englisch)

66021

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041

Accessories/ Installation Procedure

Accessories

..........1

..........2

Installation Procedure

1. To prevent short circuits, remove the key from the

ignition and disconnect the - terminal of the

battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the wire on the wiring harness.

4. Take Connector B on the wiring harness and

connect it to the speaker connector in your vehicle.

5. Take Connector A on the wiring harness and

connect it to the external power connector on your

vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

8. Reconnect the - terminal of the battery.

9. Press the reset button.

• Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and wiring

work to professionals.

• Make sure to ground the unit to a negative 12V DC power

supply.

• Do not install the unit in a spot exposed to direct sunlight

or excessive heat or humidity. Also avoid places with too

much dust or the possibility of water splashing.

• Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

• If the power is not turned ON (“PROTECT” is displayed),

the speaker wire may have a short-circuit or touched the

chassis of the vehicle and the protection function may

have been activated. Therefore, the speaker wire should be

checked.

• Make sure that all wire connections are securely made by

inserting jacks until they lock completely.

• If your vehicle’s ignition does not have an ACC position, or

if the ignition wire is connected to a power source with

constant voltage such as a battery wire, the power will not

be linked with the ignition (i.e., it will not turn on and off

along with the ignition). If you want to link the unit’s power

with the ignition, connect the ignition wire to a power

source that can be turned on and off with the ignition key.

• Use a commercially available conversion connector if the

connector does not fit in the vehicle connector.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

• If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to

work if you share the - wires or ground them to any metal

part in the car.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

• Mount the unit so that the mounting angle is 30° or less.

About CD players/disc changers connected

to this unit

Kenwood disc changers/ CD players released in 1998

or later can be connected to this unit.

Refer to the catalog or consult your Kenwood dealer

for connectable models of disc changers/ CD players.

Note that any Kenwood disc changers/ CD players

released in 1997 or earlier and disc changers made by

other makers cannot be connected to this unit.

Connecting unsupported disc changers/CD players to

this unit may result in damage.

Set the “O-N” Switch to the “N” position for the

applicable Kenwood disc changers/ CD players.

The functions you can use and the information that

can be displayed may differ depending on the models

being connected.

B64-3958-00_English_E_r1.indd 18B64-3958-00_English_E_r1.indd 18 07.11.9 4:45:25 PM07.11.9 4:45:25 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KDC-W5541 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KDC-W5541

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info