Bedienungsanleitung Kenwood KDC-W7537U (Seite 38 von 48) (Englisch)

62512

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Accessories/ Installation Procedure

Accessories

..........1

..........2

..........1

..........2

..........1

Installation Procedure

1. To prevent short circuits, remove the key from the

ignition and disconnect the - terminal of the

battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the wire on the wiring harness.

4. Take Connector B on the wiring harness and

connect it to the speaker connector in your vehicle.

5. Take Connector A on the wiring harness and

connect it to the external power connector on your

vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

8. Reconnect the - terminal of the battery.

9. Press the reset button.

• If the power is not turned ON ("Protect" is displayed), the

speaker wire may have a short-circuit or touched the

chassis of the vehicle and the protection function may

have been activated. Therefore, the speaker wire should be

checked.

• If your car is not prepared for this special connection-

system, consult your Kenwood dealer.

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

• Make sure that all wire connections are securely made by

inserting jacks until they lock completely.

• If your vehicle’s ignition does not have an ACC position, or

if the ignition wire is connected to a power source with

constant voltage such as a battery wire, the power will not

be linked with the ignition (i.e., it will not turn on and off

along with the ignition). If you want to link the unit’s power

with the ignition, connect the ignition wire to a power

source that can be turned on and off with the ignition key.

• If the fuse blows, first make sure that the wires have not

caused a short circuit, then replace the old fuse with one

with the same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent short circuits, also do not remove

the caps on the ends of the unconnected wires or the

terminals.

• Connect the speaker wires correctly to the terminals to

which they correspond. The unit may receive damage or fail

to work if you share the - wires and/or ground them to

any metal part in the car.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• If the console has a lid, make sure to install the unit so

that the faceplate does not hit the lid when closing and

opening.

• Mount the unit so that the mounting angle is 30° or less.

If You Want to Connect iPod

iPod

AUDIO OUT

KCA-iP200 (Optional accessory)

AUX input

• No other optional accessory can be connected because

the USB connector and the AUX input are used for iPod

connection.

• Dual Zone System in <Audio Setup> (page 8) will become

unavailable.

English

B64-3629-00_00.Indd 38B64-3629-00_00.Indd 38 07.1.6 6:25:30 PM07.1.6 6:25:30 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KDC-W7537U Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KDC-W7537U

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info