Bedienungsanleitung Kenwood KDV-C840 (Seite 4 von 40) (Englisch)

36090

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

— 4 —

English

Safety precautions

To prevent injury or fire, take the

following precautions:

• When extending the ignition, battery, or

ground wires, make sure to use automotive-

grade wires or other wires with a 0.75mm

(AWG18) or more to prevent wire

deterioration and damage to the wire

coating.

•To prevent a short circuit, never put or leave

any metallic objects (such as coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

To prevent damage to the unit, take

the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

•To prevent a short circuit when replacing a

fuse, first disconnect the wiring harness.

2CAUTION

2WARNING

• Do not use your own screws. Use only the

screws provided. If you use the wrong

screws, you could damage the unit.

• If you experience problems during

installation, consult your Kenwood dealer.

• The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the display

in the illustrations may differ from what

appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

The marking of products using lasers

(Except for some areas)

The label is attached to the chassis/case and

says that the component uses laser beams

that have been classified as Class 1. It

means that the unit is utilizing laser beams

that are of a weaker class. There is no

danger of hazardous radiation outside the

unit.

CLASS 1

LASER PRODUCT

NOTE

IMPORTANT INFORMATION

You can enjoy a DVD with this unit alone when

connecting it to an external monitor or audio

equipment.

Also, you can operate this unit connected to a

center unit made by Kenwood to output

sound.

A Kenwood-made center unit that can be

connected to this unit is called “Center Unit”.

About a center unit that can be

connected to this unit:

If a center unit (such as CD receivers) has

capability for “N” of <“O-N” switch>, this unit

can be connected to this unit.

According to the operating instructions of a

center unit, the setting of <“O-N” switch> is

“N”. This unit is, however, exclusive to “N”.

Therefore, <“O-N” switch> is unnecessary.

If using a separate CD/MD changer switching

unit “KCA-S210A”, you can connect this unit

to a center unit with disc changer control that

has no capability for “N”.

See the operating instructions attached to

KCA-S210A for details of connection.

The functions available and/or information

displayable may depend on types of units to

which you connect.

KDV-C810_U.S 02.2.15 10:56 AM Page 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KDV-C840 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info