Bedienungsanleitung Kenwood KM 070 (Seite 12 von 164) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

465350

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

display

For your safety the mixer is fitted with 5 separate safety sensors which will operate when using the mixer in the

cooking mode. If the mixer is switched on and a safety sensor activated, the timer/temperature display will show

n error message e.g. ‘E:01’. This will be accompanied by a beeping sound and the mixer will not work. Check

he following error messages:-

If these or any other error codes continue to appear on the display contact Kenwood Customer Care.

to use the countdown timer

The timer can be used in both the cooking and non cooking modes. If a countdown time is not selected, the

timer will automatically count up in 1 second intervals whilst the mixer is in operation. The maximum running time

is 3 hours.

1 Connect the mixer to the power supply. The display will briefly show and then clear leaving the power on

indicator visible .

2 Press either the + or – button and 0:00 will appear in the display.

3 Press either the + or – button until the desired time is displayed. The timer will count up in 5 second intervals. If

the button is pressed continuously the numbers will change more quickly the longer it is held down. A maximum

time of 3 hours can be set.

Note: If the + button is pressed when the timer is at 3:00 the displayed time will change to 0:00. If the – button is

pressed when the timer is at 0:00 the displayed time will change to 3:00.

4 Turn the speed control to the desired speed, the mixer will start and the timer will count down in 1 second

intervals.

●

The mixer operation can be paused at any time by turning the speed control to the off ‘O’ position. This will also

pause the timer. The timer will continue to count down when the mixer is re-started.

5 The mixing process will automatically stop when the total time has elapsed and audible beeps will be emitted for

3 seconds. The display will flash for 5 seconds and then clear showing the power on indicator .

to reset the timer

1 Zero the timer by pressing the + and – buttons at the same time (the speed control must be in the off ‘O’ position).

●

If the machine has been idle for 10 minutes, the LCD display and backlight will enter ‘sleep mode’ and all the

displays will turn off. If any button or control knob is activated, the display will resume its previous format.

Error Message Description Solution

The head of the machine is in the raised position. Close the head. Turn the speed control

When the head is lifted, a safety sensor disables to the ‘O’ position and then select the

E:01

he motor and heater. If the speed control is desired speed.

turned to any setting other than the Off ‘O’

position when the head is raised, this message

is displayed and the motor will not switch on.

he Cooking Chef Bowl is not fitted. The heating Ensure that the Cooking Chef bowl is

function will only work if the Cooking bowl is being used. Check that the bowl

E:02 being used. This bowl must also be correctly is fitted correctly. Turn the speed

fitted. Safety sensors will detect an incorrect control to “0” and then select desired

bowl or the correct bowl incorrectly fitted. speed.

The heat shield is not fitted. The heating function Ensure the heat shield is fitted

E:03 will be disabled if the heat shield is not correctly correctly. Turn the speed control to ‘O’

fitted. and then select desired speed.

he slow speed outlet and high speed/medium Ensure that all covers are fitted correctly.

peed outlet covers are not fitted. These covers Turn the speed control to ‘O’ and then

are fitted with safety sensors. If the covers are select desired speed.

E:04 not fitted correctly the heating will switch off and

if stir functions are selected, the motor will run

continuously. Mixing speeds min to max will

run continuously.

Temperature sensor problem. If the heater Turn the speed control to ‘O’, unplug the

control detects a bowl temperature higher than machine and allow to cool. Check

E:09 expected during normal use, the motor and that the bowl base and temperature

heater will automatically switch off. sensors are clean. Replace plug and

switch on as normal.

Motor speed or overheat problem. If the motor Turn the speed control to ‘O’ and unplug

E:10

stalls or gets too hot, the control system will the machine. Remove any obstructions

automatically switch off the motor and heater. causing the motor to stall. Ensure all

the air vents are clear of obstructions.

Plug in and switch on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KM 070 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info