Bedienungsanleitung Kenwood KM08 Cooking Chef (Seite 9 von 197) (Englisch, Dänisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

630917

Zoom out

Zoom in

Vorherige Seite

1/197

Nächste Seite

adjusting the height of the tools

Please refer to page 11 on how to assemble the mixer.

whisk, stainless steel K beater, stirring tool

For best performance the whisk, K beater and stirring tool should be

lmost touching the bottom of the bowl

.

If necessary adjust the height

using the spanner provided.

Here’s how:

Unplug the appliance.

Raise the mixer head and insert the whisk, beater or stirring tool.

3 Lower the mixer head. If the clearance needs to be adjusted, raise the

mixer head and remove the tool.

4 Using the spanner provided loosen the nut

 sufficiently to allow

djustment of the shaft

.

To lower the tool closer to the bottom of the

owl, turn the shaft anti-clockwise. To raise the tool away from the bottom

of the bowl turn the shaft clockwise.

5 Re-tighten the nut.

6 Fit the tool to the mixer and lower the mixer head. (Check its position see

oints above).

7 Repeat the above steps as necessary until the tool is set correctly. Once

this is acheived tighten the nut securely.

high temperature flexible beater - this tool should just touch the

bottom of the bowl.

dough hook - this tool is set at the factory and should require no

adjustment.

to fit and use your splashguard

assembly

The splashguard assembly consists of 2 pieces: the heat shield and the

splashguard.

The heat shield must be fitted during cooking operations

otherwise the mixer will not operate and error code E:03 will

be displayed. The heat shield is to protect the mixer head from steam

produced during the cooking process.

If necessary both the heat shield and the splashguard can be fitted to retain

ingredients in the bowl e.g. when mixing light ingredients such as flour and

icing sugar, or when cooking ingredients where moisture needs to be

retained in the bowl. The splashguard should not be fitted to the bowl

unless used in conjunction with the heat shield.

1 Raise the mixer head until it locks.

2 Push the heat shield upwards onto the underside of the mixer head

 until

fully located. The heat shield must never be used without the rubber seal

correctly fitted.

3 Fit the bowl onto the base.

4 Lower the mixer head.

5 Rest the splashguard on the bowl rim and then slide forward until fully

located

.

●

During mixing, ingredients can be added directly to the bowl via the feed

chute.

6 To remove the splashguard simply slide it away from the appliance.

7 To remove the heat shield, raise the mixer head until it locks. Remove the

tool, then pull the heat shield downwards from the underside of the mixer

head.

Note: Only fit or remove the splashguard when the mixer head is in the

locked position.











Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KM08 Cooking Chef Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KM08 Cooking Chef

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info