Bedienungsanleitung Kenwood KMM-BT209 (Seite 33 von 148) (Deutsch, Englisch, Holländisch, Französisch)

796167

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

ENGLISH 25

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

[BRIGHTNESS] Sets the brightness for day and night separately.

[DAY]/[NIGHT]: Select day or night.

Select a zone. (See the illustration on page 24.)

[LVL00] to [LVL31]: Set the brightness level.

[TEXT SCROLL] [ONCE]: Scrolls the display information once. ; [AUTO]: Repeats scrolling at

5-second intervals. ; [OFF]: Cancels.

[LEVEL METER] For / :

[ON]: Shows the level meter on the display window (as shown below). ;

[OFF]: Cancels.

Level meter

[CLOCK]

[CLOCK DISPLAY] [ON]: The clock time is shown on the display even when the unit is turned

off. ; [OFF]: Cancels.

[DEMO MODE] [ON]: Activates the display demonstration automatically if no operation is

done for about 15 seconds. ; [OFF]: Deactivates.

Preset color:

[INITIAL COLOR]

[VARIABLE SCAN]

[CUSTOM R/G/B]

[RED1]

[RED2]

[RED3]

[PURPLE1]

[PURPLE2]

[PURPLE3]

[PURPLE4]

[BLUE1]

[BLUE2]

[BLUE3]

[SKYBLUE1]

[SKYBLUE2]

[LIGHTBLUE]

[AQUA1]

[AQUA2]

[GREEN1]

[GREEN2]

[GREEN3]

[YELLOWGREEN1]

[YELLOWGREEN2]

[YELLOW]

[ORANGE1]

[ORANGE2]

[ORANGERED]

Display Settings Installation/Connection

This section is for the professional installer.

For safety’s sake, leave wiring and mounting to professionals. Consult the

car audio dealer.

WARNING

• The unit can only be used with a 12V DC power supply, negative ground.

• Disconnect the battery’s negative terminal before wiring and mounting.

• Do not connect Battery wire (yellow) and Ignition wire (red) to the car

chassis or Ground wire (black) to prevent a short circuit.

• To prevent short circuit:

– Insulate unconnected wires with vinyl tape.

– Be sure to ground this unit to the car’s chassis again after installation.

– Secure the wires with cable clamps and wrap vinyl tape around the wires

that comes into contact with metal parts to protect the wires.

CAUTION

• Install this unit in the console of your vehicle. Do not touch the metal parts

of this unit during and shortly after use of the unit. Metal parts such as the

heat sink and enclosure become hot.

• Do not connect the wires of speakers to the car chassis or Ground wire

(black), or connect them in parallel.

• Mount the unit at an angle of less than 30°.

• If your vehicle wiring harness does not have the ignition terminal, connect

Ignition wire (red) to the terminal on the vehicle’s fuse box which provides

12 V DC power supply and is turned on and off by the ignition key.

• Keep all cables away from heat dissipate metal parts.

• After the unit is installed, check whether the brake lamps, blinkers, wipers,

etc. on the car are working properly.

• If the fuse blows, first make sure the wires are not touching car’s chassis,

then replace the old fuse with one that has the same rating.

KMM-BT358_E_B5A-3849-00_EN_1st Draft.indd 25KMM-BT358_E_B5A-3849-00_EN_1st Draft.indd 25 9/7/2021 9:14:04 AM9/7/2021 9:14:04 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KMM-BT209 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info