Bedienungsanleitung Kenwood KOS-A210 (Seite 29 von 40) (Englisch)

465257

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

English

Installation Procedure

1. To prevent a short circuit, remove the key from the

ignition and disconnect the - battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the wiring harness wires in the following

order: ground, battery, ignition.

4. Connect the wiring harness connector to the unit.

5. Install the unit in your car.

6. Reconnect the - battery.

2WARNING

If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always connect those

wires to the power source running through the fuse box.

• Do not install the controller and display unit on the surface

where your vision is blocked and driving interfered.

• Before installation, check that no fuel tank, pipe, nor wire

exists at backside of the mounting surface, to prevent

screws from penetrating into such component.

• Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and wiring

work to professionals.

• Make sure to ground the unit to a negative 12V DC power

supply.

• Do not install the unit in a spot exposed to direct sunlight

or excessive heat or humidity. Also avoid places with too

much dust or the possibility of water splashing.

• Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

• If your car’s ignition does not have an ACC position, connect

the ignition wires to a power source that can be turned on

and off with the ignition key. If you connect the ignition

wire to a power source with a constant voltage supply, as

with battery wires, the battery may die.

• If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one

with the same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps

on the ends of the unconnected wires or the terminals.

• After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

Installation for Display Unit

Installation location and cleaning

Select for installation a location where the stand can

be placed completely horizontal shown in Figure A.

Do not install in locations where the entire support is

at a diagonal such as in Figure B or where the display

unit is facing down such as in Figure C.

• Thoroughly wipe away and dust or grease from the

installation location using a cloth which has been soaked in

a neutral cleaning agent and wrung out. Attach the stand

after allowing the installation location to dry.

• Do not attach the double-sided tape more than once or

touch the adhesive with your fingers as this will weaken its

adhesive strength.

• If the temperature of the surface of the installation location

is low, warm it up using a heater or other means before

attaching the stand. Low temperature may weaken the

adhesive strength of the tape.

• The supplied stand is specially intended for this product. Do

not use it with another display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KOS-A210 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KOS-A210

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info