Bedienungsanleitung Kenwood KRC-36 (Seite 23 von 122) (Englisch, Holländisch, Italienisch, Spanisch)

42699

Zoom out

Zoom in

Vorherige Seite

1/122

Nächste Seite

— 23 —— 23 —

The use of any accessories except for those provided might result in

damage to the unit. Make sure only to use the accessories shipped with

the unit, as shown above.

..........................................1

..........................................2

..........................................1

External view Number of items

1. To prevent short circuits, remove the key from the ignition and

disconnect the - terminal of the battery.

2. Make the proper input and output wire connections for each unit.

3. Cars with an ISO connector:

Connect the speaker connector of the car to Connector B of the

unit, and then connect the external power connector to

Connector A.

Cars without an ISO connector:

First connect the wire of the wiring harness, and then connect

the wiring harness connector to the unit.

4. Install the unit in your car.

5. Reconnect the - terminal of the battery.

6. Press the reset button.

If you connect the ignition wire (red) and the battery wire (yellow)

to the car chassis (ground), you may cause a short circuit, that in

turn may start a fire. Always connect those wires to the power

source running through the fuse box.

• If your car is not prepared for this special connection-system,

consult your Kenwood dealer.

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

• Make sure that all wire connections are securely made by

inserting jacks until they lock completely.

• If your vehicle's ignition does not have an ACC position, or if the

ignition wire is connected to a power source with constant

voltage such as a battery wire, the power will not be linked with

the ignition (i.e., it will not turn on and off along with the

ignition). If you want to link the unit's power with the ignition,

connect the ignition wire to a power source that can be turned

on and off with the ignition key.

• If the fuse blows, first make sure that the wires have not caused

a short circuit, then replace the old fuse with one with the same

rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent short circuits, also do not remove the caps

on the ends of the unconnected wires or the terminals.

• Connect the speaker wires correctly to the terminals to which

they correspond. The unit may receive damage or fail to work if

you share the - wires and/or ground them to any metal part in

the car.

• When only two speakers are being connected to the system,

connect the connectors either to both the front output terminals

or to both the rear output terminals (do not mix front and rear).

For example, if you connect the + connector of the left speaker

to a front output terminal, do not connect the - connector to a

rear output terminal.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• If the console has a lid, make sure to install the unit so that the

faceplate does not hit the lid when closing and opening.

2CAUTION

2WARNING

Accessories

Installation Procedure

KRC-394(E)_U.S r1 02.9.24 11:11 AM Page 23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KRC-36 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info