Bedienungsanleitung Kenwood krc-597 (Seite 31 von 36) (Englisch)

163236

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

— 31 —

What might seem to be a malfunction in your unit may

just be the result of slight misoperation or miswiring.

Before calling service, first check the following table

for possible problems.

General

? The power does not turn ON.01

✔ The fuse has blown.

☞ After checking for short circuits in the wires, replace the fuse with

one with the same rating.

? There’s a source you can’t switch.07

✔ There’s no media inserted.

☞ Set the media you want to listen to. If there’s no media in this

unit, you can't switch to each source.

✔ The Disc changer isn’t connected.08

☞ Connect the Disc changer. If the Disc changer isn’t connected to

it's input terminal, You can't switch to an external disc source.

? The memory is erased when the ignition is turned OFF.10

✔ The ignition and battery wire are incorrectly connected.11

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

? The TEL mute function does not work.15

✔ The TEL mute wire is not connected properly.

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

? The TEL mute function turns ON even though the TEL mute wire is

not connected.16

✔ The TEL mute wire is touching a metal part of the car.

☞ Pull the TEL mute wire away from the metal part of the car.

? Even if Loudness is turned ON, high-pitched tone isn't compensated

for. 17

✔ Tuner source is selected.

☞ High-pitched tone isn't compensated for when in Tuner source.

? No sound can be heard, or the volume is low.

✔ The fader or balance settings are set all the way to one side.21

☞ Center the fader and balance settings.

✔ The input/output wires or wiring harness are connected incorrectly.22

☞ Reconnect the input/output wires or the wiring harness correctly.

See the section on <Connecting Wires to Terminals>.

✔ The cassette tape is bad.23

☞ Try playing another cassette tape. If works fine, the first tape was

bad.

✔ The values of Volume offset are low.24

☞ Turn up the Volume offset, referring to the section on <Audio

control> (page 6).

? The sound quality is poor or distorted.25

✔ One of the speaker wires is being pinched by a screw in the car.

☞ Check the speaker wiring.

✔ The tape head is dirty.26

☞ Clean the tape head.

✔ The speakers are not wired correctly.27

☞ Reconnect the speaker wires so that each output terminal is

connected to a different speaker.

? Even though Synchronize Clock is ON, the clock can’t be adjusted.35

✔ The received RDS station isn’t sending time data.

☞ Receive another RDS station.

Tuner source

? Radio reception is poor.39

✔ The car antenna is not extended.

☞ Pull the antenna out all the way.

✔ The antenna control wire is not connected.40

☞ Connect the wire correctly, referring to the section on

<Connecting Wires to Terminals>.

Troubleshooting Guide

KRC-597(E)_U.S 03.10.7 6:48 PM Page 31

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood krc-597 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood krc-597

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info