Bedienungsanleitung Kenwood KRF-V7060D (Seite 9 von 44) (Englisch)

40355

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Make connections as shown in the following pages.

When connecting the related system components, be sure

to refer to the instruction manuals supplied with the compo-

nents you are connecting.

Do not connect the power cord to a wall outlet until all

connections are completed.

Notes

Be sure to insert all connection cords securely. If their connections are

imperfect, sound may not be produced or there will be noise inference.

2. Be sure to remove the power cord from the AC outlet before plugging

or unplugging any connection cords. Plugging/unplugging connection

cords without disconnecting the power cord can cause malfunctions

and may damage the unit.

3. Do not connect power cords from components whose power con-

sumption is larger than what is indicated on the AC outlet at the rear

of this unit.

Analog connections

Audio connections are made using RCA pin cords. These cables transfer

stereo audio signal in an “analog” form. This means the audio signal

corresponds to the actual audio of two channels. These cables usually

have 2 plugs on each end, one red for the right channel and one white for

the left channel. These cables are usually packed together with the

source unit, or are available at your local electronics retailer.

Microcomputer malfunction

If operation is not possible or an erroneous display appears, even

though all connections have been made properly, reset the micro-

computer referring to “In case of difficulty”. ‚

CAUTION

Be sure to adhere to the following, or proper ventilation will be

blocked causing damage or fire hazard.

• Do not place any objects impairing heat radiation onto the top of the

unit.

• Leave some space around the unit (from the largest outside

dimension including projection) equal to or greater than, shown

below.

Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm

Setting up the system

Input mode settings

CD/DVD, VIDEO 2 and DVD/6CH inputs each include jacks for digital

audio input and analog audio input.

You must select beforehand which type of input is to be used for each

connected component.

The initial factory settings for audio signal playback for CD/DVD,

DVD/6CH and VIDEO 2 are full auto.

To use the analog audio input for playback instead (if, for example, you

have connected a VCR to the VIDEO2 input), you must set the input

mode for the corresponding input to the analog mode.

After completing connections and turning on the receiver, follow the

steps below.

INPUT MODE

Input Selector

1 Use the Input Selector keys to select CD/DVD, VIDEO 2 or

DVD/6CH.

2 Press the INPUT MODE key.

Each press switches the setting as follows:

In DTS play mode

1 FULL AUTO (digital input, analog input)

2 DIGITAL MANUAL (digital input)

In CD/DVD, VIDEO 2, DVD/6CH play mode

1 FULL AUTO (digital input, analog input)

2 DIGITAL MANUAL (digital input)

3 6CH INPUT (DVD/6CH input)

4 ANALOG (analog input)

Digital input:

Select this setting to play digital signals from a DVD, CD, or LD

player.

Analog input:

Select this setting to play analog signals from a cassette deck, VCR,

or record player.

Auto detect:

In “FULL AUTO” mode (AUTO DETECT indicator light up), the

receiver detects the digital or analog input signals automatically.

Priority is given to digital signal during input mode selection. The

receiver will select the input mode and listening mode automatically

during playback to match the type of input signal (Dolby Digital,

PCM, DTS) and the speaker setting. The OPTICAL and COAXIAL

indicator on the display will light up when digital signal is detected.

If the input signal is analog, the ANALOG indicator will light up.

To keep the receiver set to the currently selected listening mode,

use the INPUT MODE key to select “DIGITAL MANUAL” (manual

sound). However, even when this setting is selected, there may be

cases in which the listening mode is selected automatically to

match a Dolby Digital source signal depending on the combination

of listening mode and source signal.

If the INPUT MODE key is pressed quickly, sound may not be

produced. Press the INPUT MODE key again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KRF-V7060D Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KRF-V7060D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info