Bedienungsanleitung Kenwood KRF-V7060D (Seite 40 von 44) (Englisch)

40355

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

In case of difficulty

Tuner

Cause

• No antenna is connected.

• The broadcast band is not set properly.

• The frequency of the desired station is not

tuned.

• Noise due to ignition noise from an automo-

bile.

• Noise due to interference from an electric

appliance.

• Noise due to a nearby TV set.

• The preset station belongs to a frequency that

cannot be received.

• The preset memory was cleared because the

power cord had been unplugged for a long

period of time.

Remedy

• Connect an antenna. ^

• Set the broadcast band properly.

• Tune the frequency of the desired station.

• Install the outdoor antenna away from the

road.

• Turn off the power to the appliance.

• Install the receiver farther away from the TV.

• Preset a station with a receivable frequency.

• Preset the station again.

Symptom

Radio stations cannot be received.

Interference.

A station which was preset cannot be re-

ceived by pressing the corresponding nu-

meric key.

Amplifier

Cause

• The speaker cords are disconnected.

• VOLUME is set to the minimum position.

• MUTE is ON.

• The SPEAKERS switches are set to OFF.

• Speaker cords are short-circuited.

• The speaker cord is disconnected.

• The surround speaker cords and/or the center

speaker cord is disconnected.

• A surround mode has not been engaged.

• The surround and/or center volume controls

are set to the minimum level.

• The audio cord from the record player is not

connected to the PHONO jacks.

• The record player is not grounded.

• There are many possible causes for this prob-

lem, depending on the type of DVD player

used.

• The input mode is set to digital manual.

• The software is copy-guarded.

Remedy

• Connect them properly referring to “Connect-

ing the speakers” $

• Adjust the volume to a proper level.

• Turn OFF the MUTE. ™

• Set the SPEAKERS switches to ON. ¡

• Turn the power off, eliminate the short-circuit-

ing, then turn on the power again.

• Connect it properly referring to “Connecting

the speakers”. $

• Connect it properly referring to “Connecting

the speakers”. $

• Select a surround mode.

• Adjust the speaker levels using the test tone.

(

• Insert the audio cord plugs securely into the

PHONO jacks.

• Connect the grounding wire to the GND termi-

nal on the rear panel.

• Set the input mode to digital manual before

starting playback of the Dolby Digital source.

• Press the INPUT MODE key to select to full

auto mode. 9

• Copy-guarded video software cannot be re-

corded.

Symptom

No sound from the speakers.

The standby indicator blinks and sound is

not output.

Sound is not output from one of the speakers.

Sound is not output from the surround

speakers and / or the center speaker, or their

sound is very small.

A humming noise is generated when the

PHONO input selector is selected.

When playing a Dolby Digital source signal

using a DVD player, the sound is cut off soon

after it starts.

No sound is produced during playback from

a DVD player.

A video source cannot be recorded

normally.

Resetting the Microcomputer

The microcomputer may malfunction (unit cannot be operated, or

shows an erroneous display) if the power cord is unplugged while

the power is ON, or due to some other external factor. If this

happens, execute the following procedure to reset the microcom-

puter and return the unit to its normal operating condition.

• Please note that resetting the microcomputer will clear the contents

of the memory and returns the unit to the state it was in when it left

the factory.

For the U.S.A. and Canada

Unplug the power cord from the wall outlet, then plug it

back in while holding down the POWER ON/STANDBY

key.

For other countries

With the power cord plugged in, turn the POWER ON/

OFF key OFF. Then, while holding down the ON/

STANDBY

key, press POWER ON/OFF.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KRF-V7060D Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KRF-V7060D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info