Bedienungsanleitung Kenwood KVR-A7O (Seite 7 von 14) (Englisch)

617939

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

uP/DowN TUNTNG buttons

Auto

tuning mode

When the

or DOWN button

pressed,

the frequency

automatically

increases

decreases

until

the next station of sufficient signal

strength is reached.

Manual

tuning

mode

Each time the UP or

DOWN

button is

pressed,

the tuned frequency

increases

decreases in the following manner.

50 kHz steps

AM-9kHzsteps

either button

is held down more than half a second, the

tuned

frequency

will continue to increase or decrease un-

til

the button is released.

rurunue MoDE

buttons

AUTO/MANUAI

button

Each

press

alternates auto

tuning

and

manual tuning modes.

DIRECT

button

Press this

button

while listening to

radio

broadcast to set the unit to the direct tuning

mode

that the frequency oÍ the desired station can be

entered with the numeric buttons.

PRESET

FUNcnoN bunon

Used to

select A or B setting for the

preset

channel button. ln

either FM

AM mode, 20

stations can be

preset

as random

as each

setting

can contain

preset

stations.

ln-

dicator A lights when A setting is

used, and

indicator B lights

when

setting

used.

DIRECT

ACCESS TUNING/PRESET

(numericl

buttons

Use these buttons to:

input

directly the digits of frequencies, or

store

and recall frequencies

the

preset

memory.

The

controls and switches

equalizer

section.

"ta

for

graphic

eoueuzER

PRESET MEMoRY

bunon

Press

this

button to store equalizer curves

in memory. When

this

button is

pressed

with

the display

window in

graphic

equalizer mode.

the

MEMORY indicator lights

and

the

"<"

the

sides

of the display

window's

displays

1 to

flash, in-

dicating that memory operation is

possible.

During

this

condition,

which lasts Íor approx. 5 seconds.

pressing

one oÍ EOUALIZEB PRESET buttons

to 3 stores the

current

equalizer curve in the memory of the button

pressed.

eoult-lzER

PRESET buttons

Use these

buttons to store equalizer curves

in memory

or to

recall them.

(Three

different equalizer curves can be stored.)

either

case, when the display

window

mode

has

been set

for

the music spectrum analyzer display"

the

graphic

equalizer display

displayed for approx. 5 seconds,

then

the

display

reverts to

the

spectrum

analyzer

display.

LoUDNESS

bufton

Press

this

button

to recall the

preset

(Íixed)

equalizer curve

(We

call

this LOUDNESS curve).

pneseNCE

button

Press

this

button to

recall

the

preset

(Íixed)

equalizer curve

(We

call

this PRESENCE curve).

EOUAUZER switch

Turn

this

switch

to ON and the frequency characteristic will

modiÍied

passing

through the

graphic

equalizer. ln the

DEFEAT,

position.

the

frequency

characteristic

remains

un-

changed.

The DEFEAT

indicator in the display window lights when the

switch

set

to DEFEAT.

REMOTE SENSOR

Point the supplied

remote

control unit

towards this sensor

and

operate.

PowER srAND

BY indicator

Lights when the

MAIN POWER

switch

is set to ON.

BAIÁNCE controls

Governs

the amount

of sound coming from each

paired

speakers

get

optimum

stereo

effect.

Pressing the RIGHT button will decrease the left channel

volume and

pressing

the LEFT button will decrease the right

channel

volume. When the BALANCE controls

pressed,

display

window shows the BALANCE

indicator.

MUTTNG bunon

When the

muting

button

pressed.

the MUTING indicator in

the display window

will Ílash,

and

the overall listening

sound

level

is reduced

20 dB.

When the button

pressed

again,

you

can

restore

exactly the

same

listening

level

as before.

volume

conrÍots

This

control adjusts

the left- and right-channel volumes

simultaneously.

Set it for the deslred

listening

level. Pressing

the

(A)

button

increases the volume and

pressing

the

down

(V)

button decreases

it.

Note:

A slight

noise is heard from the

speakers

when operating the

VOLUME controls. This

noise is

the built-in microprocessor control

signal and

is not

fault.

vPeO

switch

play

a video recorder connected to the

VCR A

jacks,

set

the switch to A. To

play

back a video

recorder

connected to

the VCR B

jacks,

set the switch to

SYNTHETIC STEREO SWitCh

Press this switch

give

the

pseudo

stereo effect to the

monaural source connected to the VCR A and B

jacks.

NPUT

sELEcroR

buttons

PHONO

Selects the

program

source

played

on the

turntable.

TUNER

Selects the tuner

mode.

CD/AUX

Selects

the

source connected

to the CD/AUX

jacks.

VIDEO

Selects the

video recorders

connected

to the

VCR

jacks. (Use

the VIDEO

switch

Íor

selection

between

the

VCR A

jacks

and VCR B

jacks.)

TAPE 1

Press this button to

play

back a

tape

deck

connected to TAPE

jacks.

TAPE

Press this button

play

back a

tape

deck

connected

to the TAPE 2

jacks.

(The

TAPE-2 switch is

operated

priority

to any

other

audio input systems.)

KVR-A7OR

(E}

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KVR-A7O Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info