Bedienungsanleitung Kenwood KVT-827DVD (Seite 3 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Alle Sprachen)

446134

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

English

Installation Procedure

1. To prevent a short circuit, remove the key from the

ignition and disconnect the - battery.

2. Make the proper input and output wire connections

for each unit.

3. Connect the speaker wires of the wiring harness.

4. Take Connector B on the wiring harness and

connect it to the speaker connector in your vehicle.

5. Take Connector A on the wiring harness and

connect it to the external power connector on your

vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

8. Reconnect the - battery.

9. Press the reset button.

2WARNING

• If you connect the ignition wire (red) and the

battery wire (yellow) to the car chassis (ground),

you may cause a short circuit, that in turn may start

a fire. Always connect those wires to the power

source running through the fuse box.

• Do not cut out the fuse from the ignition wire (red)

and the battery wire (yellow). The power supply

must be connected to the wires via the fuse.

2CAUTION

• If the power is not turned ON (or it is ON, but

will be OFF immediately), the speaker wire may

have a short-circuit or touched the chasis of the

vehicle and the protection function may have been

activated. Therefore, the speaker wire should be

checked.

• If your car’s ignition does not have an ACC position,

connect the ignition wires to a power source that

can be turned on and off with the ignition key. If

you connect the ignition wire to a power source

with a constant voltage supply, as with battery

wires, the battery may die.

• If the console has a lid, make sure to install the

unit so that the faceplate will not hit the lid when

closing and opening.

• If the fuse blows, first make sure the wires aren’t

touching to cause a short circuit, then replace the

old fuse with one with the same rating.

• Insulate unconnected wires with vinyl tape or other

similar material. To prevent a short circuit, do not

remove the caps on the ends of the unconnected

wires or the terminals.

• Connect the speaker wires correctly to the terminals

to which they correspond. The unit may be

damaged or fail to work if you share the - wires or

ground them to any metal part in the car.

• When only two speakers are being connected to the

system, connect the connectors either to both the

front output terminals or to both the rear output

terminals (do not mix front and rear). For example,

if you connect the + connector of the left speaker

to a front output terminal, do not connect the -

connector to a rear output terminal.

• After the unit is installed, check whether the brake

lamps, blinkers, wipers, etc. on the car are working

properly.

• Mount the unit so that the mounting angle is 30° or

less.

B54-4465-00_00.indb 3B54-4465-00_00.indb 3 05.5.18 1:29:32 PM05.5.18 1:29:32 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KVT-827DVD Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KVT-827DVD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info