Bedienungsanleitung Kenwood KVT-M707 (Seite 60 von 64) (Englisch)

465256

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

English

Troubleshooting Guide

General

The power does not turn on.

✔ The fuse has blown.

After checking for short circuits in the wires,

replace the fuse with one having the same

rating.

✔ The speaker wire has a short-circuit or touches

the chassis of the vehicle, and then the

protection function is activated.

Wire or insulate the speaker cable properly and

press the reset button.

The message "Disconnected cable found.

Please confirm a connection line." is displayed

and the unit cannot be used.

✔ Receiver unit is disconnected.

Connect the wire correctly, referring to the

section on <INSTALLATION MANUAL>.

A non-connected source cannot be selected.

✔ An optional unit required to listen to each

source is not connected yet.

A non-connected source is not selected. See

<INSTALLATION MANUAL> and connect the

unit correctly.

✔ The RESET button is not pressed yet although

the optional unit has been connected to the

system.

Press the reset button (see page 4).

✔ The "O-N" switch of the optional unit is at the

"O" position.

Set the "O-N" switch to the "N" position.

✔ A disc changer not supported by the system is

used.

Use a disc changer supported by the system

(see page 4).

Nothing happens when the buttons are

pressed.

✔ The computer chip in the unit is not

functioning normally.

Press the reset button on the unit (see page 4).

No television/video image appears.

✔ The unit is not connected to the parking brake

detection switch.

Make proper connections according to

<INSTALLATION MANUAL>.

✔ The parking brake is not engaged.

For safety reasons no television/video images

are displayed while the vehicle is moving.

Engaging the parking brake will cause images

to be displayed.

The screen is dark.

✔ The unit is in a location where temperature is

low.

If the temperature of the monitor unit drops,

the screen may appear darker when power is

first turned on due to the characteristics of a

liquid crystal panel. Wait a while after turning

power on for the temperature to rise. Normal

brightness will return.

The screen does not darken when the vehicle’s

lights are turned on.

✔ The unit is set to auto dimmer.

When the unit is set to auto dimmer, it is not

linked to the vehicle's light switch.

✔ The illumination wire has not been connected.

(If manual dimmer is set)

Make proper connections according to

<INSTALLATION MANUAL>.

AM/FM radio reception is poor and/or there is

noise.

✔ The TV antenna and vehicle‘s radio antenna are

too close.

Separate the two antennas as far as possible.

Turn off the main unit.

The remote controller does not operate.

✔ The remote control mode selector is not set

correctly.

Switch the remote control mode selector

according to the source you select (see page

10).

What might appear to be a malfunction in your unit may just be the result of slight misopera-

tion or miswiring. Before calling service, first check the following table for possible problems.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood KVT-M707 Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood KVT-M707

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info