Bedienungsanleitung Kenwood M-707I (Seite 13 von 24) (Englisch)

63925

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

English

Using the CD/USB device

Preparation

Loading a disc

1 Press CD/USB [CD/USB] button to select CD

mode.

2 Press [0] button to open the CD tray.

3 Place a disc into the tray with the label facing

up.

4 Press [0] button to close the CD tray.

For a CD, the total playtime and total number of

tracks will appear in the display.

For an audio  le-CD, the total album number and

total  le number will appear on the display.

Removing a disc

1 Press [0] button, grasp the disc by its edges,

and carefully pull it out.

2 Press [0] button to close the CD tray.

Inserting a USB device

1 Press the [ ] button to select standby

mode.

2 Insert a USB device to the USB connector on the

front panel.

3 Press CD/USB [CD/USB] button to select USB

mode.

Press the CD/USB [CD/USB] button in the CD

mode.

The total album number and total  le number will

appear on the display.

Removing the USB device

1 Press the [ ] button to select standby

mode.

2 Remove the USB device.

⁄

• To ensure good system performance; wait until the unit

completely reads the disc/USB device before proceeding.

• If the disc compartment is not loaded with a disc, “NO DISC” is

displayed. If the disc is unreadable, “CHECK DISC” is displayed.

• If the disc is unreadable or there is no playable audio file in

the USB device, “NO DATA” is displayed.

• For audio files, reading time may exceed 10 seconds due

to the large number of songs compiled into one disc/USB

device.

• The icon “MP3” appears only when an MP3-file is played.

The icon “WMA” appears only when an WMA-file is played.

• When playing or recording from/to the USB device, removing

it or turning the power off may corrupt the sound source and

get it unplayable.

Playing a CD/ audio  le

Press FWD PLAY 6 [6] button to start playback.

The track/ le number and elapsed playing time of

the current track/ le appear on the display.

Basic opertions

Operation type Operation

To stop playback Press 7 [7 stop] button.

To interrupt

playback

Press FWD PLAY 6 [6] button.

Press again to resume playback.

To search for a

particular passage

during playback

Press and hold SEARCH/TUNING 4 or

¢ [4 or ¢ search +/–] button for

more than 2 seconds.

Press the FWD PLAY 6 [6] button

when the desired passage is located.

To select a track/ file Press SEARCH/TUNING 4 or ¢ [4

or ¢ search +/–] button in play or

pause mode.

To select a album

(For audio file only)

Press P.CALL/ALBUM 5 or ∞ [p.call/

album up or down] button in play or

pause mode.

⁄

• For audio file; “DIR:xxx TRK:xxx” appears on the display. “DIR:

xxx” indicates album number and “TRK:xxx” indicates the file

number.

• The digit buttons, 0–9 on the remote control unit can also be

used to select a track/file.

Press the digit buttons as shown below:

CD Audio file

To select track/file 2 2 and ENTER 2 and ENTER

To select track/file 23 2 and 3 2, 3 and ENTER

To select file 120 — 1, 2 and 0

If the ENTER button is not pressed, the search for the selected

track/file will start in 5 seconds.

B60-5763-08_00_M-707i_English.in13 13B60-5763-08_00_M-707i_English.in13 13 08.7.9 6:15:57 PM08.7.9 6:15:57 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood M-707I Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood M-707I

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info