Bedienungsanleitung Kenwood Mini 1160 rapid (Seite 99 von 108) (Deutsch, Englisch, Französisch, Italienisch)

586255

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Problem check list

Symbols indicating a fault

 • Closetheloadingdoorproperly

F3 / • Checkwaterinlethose(themachineisnotgettingenoughwater,openthetapfully)

• Inlet sieve blocked (cleaning - see P. 97)

• Turn off main switch, wait a few moments and turn back on or turn programme selector to “  “

position

F4 The water level is too high, when you switch on the machine

• Wait until the machine has stopped pumping out water, or until the water level has returned

to normal (this is announced by a “clicking” noise)

• Turn programme selector to “

 “ position

• Turn off main switch on the machine

• Checkdrainagesystem(seeP.98)

• Turn on main switch

• Turn programme selector to spin programme P7 (water remaining in the machine will be

pumped out) or carry out emergency draining - see P. 98

• start the programm

• If the same fault occurs again

 -->Turnoffcoldtap,andremoveplugfromsocket;Contactyourcustomerservice,carryout

emergency draining (see P. 98), use emergency door opener (see P. 98) to remove washing

from machine.

F2 The washing solution is discharged very slowly, or not at all

• Turn off main switch

• Cleandrainpump(seeP.98)

• Checkdrainhoseforblockage

• Turn on main switch

• If this procedure has cured fault F2, it is possible that fault F4 may arise due to water level in

the machine being too high, this can be eliminated by carrying out procedure as described in

F4.

• start the programm

• If fault F2 occurs again

 -->Turnoffcoldtap,andremoveplugfromsocket;Contactyourcustomerservice,carryout

emergency draining (see P. 98), use emergency door opener (see P. 98) to remove washing

from machine.

Should the display show the following error codes: F1, F5 - F8, F0, F II, FC they can be deleted as

mentioned below:

• Turn on main switch

• Programm timer to P2 °C

• Press button

and simultaneously until the display shows “00” (approx. 3 sec)

You can restart the washing machine now.

Attention: If the display shows one of these error codes again, please contact your customer ser-

vice, carry out emergency draining and use emergency door opener if necessary to remove was-

hing (see P. 98).

Summary only featured on the Mini 1160 rapid The water protection device has been activated!

• Turnoffcoldlltap

• Turn off main switch

• Contactyourcustomerservice,carryoutemergencydraininganduseemergencydooropenerif

necessary to remove washing (see P. 98).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood Mini 1160 rapid Seite 99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info