Bedienungsanleitung Kenwood TH-D72A (Seite 72 von 75) (Englisch)

606703

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

SKY CMD – 2

PREPARATION FLOW

The following steps should guide you to a good start of

Sky Command operation. First connect the Transporter to

the HF transceiver.

1 <On the Commander and Transporter> Select the

same VHF and UHF frequencies.

When using the TH-D72 to communicate with the

Commander and Transporter, set the TH-D72 as

described below.

Band A: VHF frequency Band B: UHF frequency

Full Duplex: ON Tone: ON (Band B)

Band A: UHF frequency Band B: VHF frequency

Full Duplex: ON CTCSS: ON (Band A)

Note: Configure the squelch to an appropriate level for both the VHF

and UHF band on the Commander and Transporter. If the squelch

is not set to an appropriate level, the transceivers may enter a BUSY

state due to noise signals and be unable to transmit.

2 <On the Commander> Access Menu 500 to program a

callsign (9 digits max.) for the Commander.

• You may enter your exact callsign; ex. W6DJY.

3 <On the Commander> Access Menu 501 to program a

callsign (9 digits max.) for the Transporter.

• This callsign must be different from the one for the

Commander. So you may add SSID characters; ex.

W6DJY-1.

4 <On the Transporter> Access Menu 500 to program

the same callsign as you entered in step 2.

5 <On the Transporter> Access Menu 501 to program

the same callsign as you entered in step 3. The same

callsign as you entered in step 2.

6 <On the Commander and Transporter> Access Menu

502 and select the tone frequency.

• Select the same tone frequency on both transceivers.

7 <On the Commander> Access Menu 503 and select

“Commander”.

• “Push [ 0 ] key to Start Commander!!” appears.

8 <On the Transporter> Access Menu 503 and select

“Transporter”.

Now the Commander and Transporter are in Sky Command

mode. For operations in this mode, see “CONTROL

OPERATION”. First switch ON the HF transceiver and press

[SYNC] on the Commander. To exit the Sky Command

mode, access Menu 503 and select “Off”.

Note:

◆ Unless you program callsigns, you cannot select “Commander” or

“Transporter” using Menu 503.

◆ On the HF transceiver, select 9600 bps and 1 stop bit (default)

using the Menu Set-up function.

◆ Adjust the audio level on both the Transporter and HF transceiver

while listening to audio output from the Commander. An

appropriate position of the AF control on the HF transceiver might

be in the range, 8:30 to 9:00.

◆ To distinguish your various stations or nodes, you can have up

to 15 Secondary Station IDentifiers (SSIDs); ex. W6DJY-1 to

W6DJY-15. You always have to put a dash between your callsign

and SSID number.

◆ Your station’s transmit signal can be received when the receive

frequency is 3 times the transmit frequency.

Example: Transmit frequency is 146.600 MHz and receive

frequency is 438.000 MHz.

ATTENTION: Use only after verifying that there is no reception

disruption during communications.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-D72A Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-D72A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info