Bedienungsanleitung Kenwood TH-D72A (Seite 75 von 75) (Englisch)

606703

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

WIRELESS OPERATION (TH-D72A ONLY)

If you also have a Kenwood multi-band mobile transceiver, you can control one of its bands by sending DTMF tones from

this handy transceiver. You will find this function useful when you want to control your mobile transceiver from a location

outside your vehicle.

Note:

◆ You can remotely control only mobile transceivers that have both the secret number and Remote Control functions.

◆ FCC rules permit you to send control codes only on the 440 MHz band.

PREPARATION

Let us assume the VHF band of the mobile transceiver will

be controlled.

On the handy transceiver:

1 Press [PTT] + [VFO] + Power ON.

• The current secret access code number appears. The

default is 000.

2 To change the secret number, press the numeric keys

(0 to 9) to enter a 3-digit number.

• You can also press [ ]/[ ] to select each digit. Press

[

OK] (or [ESC ]) to move the cursor to the next (or

previous) digit.

3 Press [ OK] to complete the setting.

4 Select the UHF band.

5 Select the transmit frequency.

6 Turn the transceiver power OFF.

7 Press [PTT] + [MR] + Power ON.

• The transceiver enters Remote Control mode. “Mobile

Ctrl” appears.

• To exit Remote Control mode, repeat steps 6 and 7.

On the mobile transceiver:

8 Set the ID code to the same secret number you set on

the handy transceiver.

• For the method, refer to the instruction manual for the

mobile transceiver.

9 Select the receive frequency on the UHF band.

• Match this frequency with the transmit frequency of the

handy transceiver.

10 Enter the transceiver’s Remote Control mode.

• For the method, refer to the instruction manual for the

mobile transceiver. If it is not described, consult your

authorized Kenwood dealer, customer service, or service

center.

CONTROL OPERATION

When in Remote Control mode, the keys of the handy

transceiver will function as described below. Each time

you press a key, the handy transceiver will automatically

transmit the corresponding command to the mobile

transceiver.

TONE ON CTCSS ON ENT

OFF

TONE OFF CTCSS OFF TONE SEL

CALL VFO MR REP ON

DOWN LOW UP REP OFF

TM-V7/ TM-D700: Revers ON/ OFF

TM-D710/ TS-2000: DCS ON/ OFF

Other than TM-V7/ TM-D700/ TM-D710/ TS-2000:

Tone Alert ON/ OFF.

Switches Cross-band Repeater ON/ OFF if the mobile

transceiver has this function.

To change the transmit/ receive frequency:

([VFO] ➡ [ENT] ➡ [0] ~ [9] (enter the necessary digits)➡

[ENT]) or ([VFO] ➡ [ ]/[ ])

To recall a memory channel:

([MR] ➡ [ENT] ➡ [0] ~ [9] (enter the necessary digits) ➡

[ENT]) or ([MR] ➡

[ ]/[ ])

To change the tone (or CTCSS) frequency:

([TONE SEL] ➡ [0] ~ [9] (enter 2 digits; ex. [0], [5]) ➡

[TONE SEL])

• Use Nos. 01 to 42, as shown in the CTCSS table.

• Your mobile transceiver may require you to first activate the

Tone or CTCSS function. It may also allow you to program a

separate tone and CTCSS frequency. Check the instruction

manual for the mobile transceiver.

WIRELESS OP – 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-D72A Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-D72A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info