Bedienungsanleitung Kenwood TH-F7E (Seite 48 von 64) (Englisch)

511233

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

WIRELESS REMOTE CONTROL (TH-F6A ONLY)

If you also have a KENWOOD multi-band mobile

transceiver, you can control one of its bands by

sending DTMF tones from this portable transceiver.

You will find this function useful when you want to

control your mobile transceiver from a location

outside your vehicle.

Note:

◆

You can remotely control only mobile transceivers that have both

the DTSS and Remote Control functions.

◆

The FCC rules permit you to send control codes only on the

70 cm band.

PREPARATION

Let us assume the 2 m band of the mobile transceiver

will be controlled.

On the portable transceiver:

1 Press [PTT]+[VFO]+[ ] (POWER).

• The current secret access code number

appears. The default is 000.

2 Press a numeric key (0 to 9) to enter a 3-digit

secret number.

• You can also turn the Tuning control or press

[ ]/ [ ] to select each digit. Press [ ] (or [ ])

to move the cursor to the next (or previous)

digit.

3 When the cursor is at the right most position,

press [ ] to complete the setting.

4 Press [BAND] to select the 70 cm band.

5 Turn the Tuning control to select the transmit

frequency.

6 Turn a transceiver power OFF.

7 Press [PTT]+[MR]+[ ] (POWER).

• The transceiver enters Remote Control mode.

“MOBILE CTRL” appears.

• To exit Remote Control mode, repeat steps 6

and 7.

On the mobile transceiver:

8 Program the DTSS code on the 70 cm band as the

secret number.

• Select the same number as you selected in

step 2.

• For the programming method, refer to the

instruction manual of the mobile transceiver.

9 Select the receive frequency on the 70 cm band.

• Mate this frequency with the transmit frequency

on the portable transceiver.

10 Make the transceiver enter Remote Control mode.

• For the method, refer to the instruction manual

of the mobile transceiver.

CONTROL OPERATION

When in the Remote Control mode, the keys of the

transceiver will function as below. Each time you

press a key, the transceiver will automatically enter

transmit mode and send the corresponding command

to the mobile transceiver.

1 2 3 A

NOVER

NOENOTNOSSCTCTNE

4 5 6 B

FFOVER

FFOENOTFFOSSCTCLESENOT

7 8 9 C

LLACOFVRM)NOPER(

0 # D

NWODWOLPU)FFOPER(

TM-V7A/ TM-D700A:REV ON/ OFF

TS-2000/ TS-B2000: DCS ON/ OFF

Other mobile transceiver: TONE ALERT ON/ OFF

Switches Repeater function ON/ OFF if the mobile

transceiver supports this function.

To change the transmit/ receive frequency:

[VFO] ➡ [ENT] ➡ [0] ~ [9] (enter the necessary

digits) ➡ [ENT]

[VFO] ➡ [UP]/ [DOWN]

To recall a memory channel:

[MR] ➡ [ENT] ➡ [0] ~ [9] (enter the necessary digits)

➡ [ENT]

[MR] ➡ [UP]/ [DOWN]

To change the tone (or CTCSS) frequency:

[TONE SEL] ➡ [0] ~ [9] (enter 2 digits; ex. [0], [5]) ➡

[TONE SEL]

• Refer to the Tone frequency table on your mobile

transceiver for the Tone number.

• Your mobile transceiver may require you to first

activate the Tone or CTCSS function. It may also

allow you to program a separate tone and CTCSS

frequency. Refer to the instruction manual of the

mobile transceiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TH-F7E Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TH-F7E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info