Bedienungsanleitung Kenwood TM-D710GA (Seite 8 von 77) (Englisch)

606707

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

REPEATER-1

REPEATER ACCESS

Most repeaters use a receive and transmit frequency pair with

a standard or non-standard offset (odd-split). In addition, some

repeaters must receive a tone from the transceiver in order

to gain access to the repeater. For details, consult your local

repeater reference.

■ Selecting an Offset Direction

The offset direction allows your transmit frequency to be

higher (+) or lower (–) than the receive frequency.

1 Select your desired band (A or B).

2 Press [F], [SHIFT] to select an offset direction.

• Each time you press [SHIFT], the offset direction changes as

follows:

Simplex operation

➡ + ➡ – ➡ Simplex operation

• If you are using an E type transceiver, when operating on the

430 MHz band, the offset direction changes as follows:

Simplex operation

➡ + ➡ – ➡ = (–7.6 MHz) ➡ Simplex

operation

If the offset transmit frequency falls outside the allowable

range, transmitting is inhibited. Use one of the following

methods to bring the transmit frequency within the band

limits:

• Move the receive frequency further inside the band.

• Change the offset direction.

Note: While using an odd-split memory channel or transmitting, you cannot

change the offset direction.

OPERATING THROUGH REPEATERS

■ Selecting an Offset Frequency

The offset frequency is the value which the transmit

frequency will be offset from the receive frequency. The

default offset frequency on the 144 MHz band is 600 kHz for

all type versions. The default on the 430/440 MHz band is 5

MHz.

1 Select your desired band (A or B).

2 Enter Menu mode and access Menu 400.

3 Set the appropriate offset frequency value.

• The selectable range is from 00.00 MHz to 29.95 MHz, in

steps of 50 kHz.

Note: After changing the offset frequency, the new offset frequency will

also be used by Automatic Repeater Offset.

■ Activating the Tone Function

To turn the Tone function on:

1 Select your desired band (A or B).

2 Press [TONE] to turn the Tone function ON.

• Each press of [TONE] changes the selection as follows:

Tone (

) ➡ CTCSS ( ) ➡ DCS ( ) ➡ Cross Tone (

: default) ➡ Off (no display).

• The

icon appears on the display when the tone

function is ON.

Note: When accessing a repeater that requires a 1750 Hz tone, you do not

need to activate the Tone function. Simply press the key assigned to the

1750 Hz tone {Menu 906 ~ 911} to transmit the tone.

Repeaters are often installed and maintained by radio clubs, sometimes with the cooperation of local businesses involved in the

communications industry.

Compared to simplex communication, you can usually transmit

over much greater distances by using a repeater. Repeaters

are typically located on mountain tops or other elevated

locations. They generally operate at higher ERP (Effective

Radiated Power) than a typical station. This combination

of elevation and high ERP allows communications over

considerable distances.

TX: 144.725 MHz

TX tone: 88.5 Hz

RX: 145.325 MHz

TX: 144.725 MHz

TX tone: 88.5 Hz

RX: 145.325 MHz

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TM-D710GA Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TM-D710GA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info