Bedienungsanleitung Kenwood TM-D710GE (Seite 41 von 77) (Englisch)

606708

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

PACKET-3

TNC COMMANDS LIST

The commands supported by the built-in TNC are listed below. You must enter a space between a command name (or short-form) and

a parameter, or between two parameters; ex. AU OFF, BEACON EVERY 18.

Command Name Short Description Parameter Default

8BITCONV 8

When ON, handles one character using 8 bits in Converse

mode. When OFF, handles one character using 7 bits.

ON/ OFF ON

AFILTER AF

Speciﬁ es up to 4 control codes to be removed from received

packets when in Converse mode.

$00 ~ $80 $00

AUTOLF AU

When ON, sends a line feed (LF) to the computer after each

carriage return (CR).

ON/ OFF ON

AXDELAY AXD

Speciﬁ es the delay time to be added to TXDELAY between

PTT ON and start of transmission. The unit of the parameter

is 10 milliseconds.

0 ~ 120 0

AXHANG AXH

Speciﬁ es the voice repeater hang time. The unit of the

parameter is 100 milliseconds.

0 ~ 250 0

BEACON B

If set to EVERY, sends a beacon packet at intervals of the

speciﬁ ed period (n). If set to AFTER, sends a beacon packet

only once after the speciﬁ ed period (n). The unit of n is

10 seconds.

EVERY/ AFTER n

(n = 0 ~ 250)

EVERY 0

BTEXT BT

Speciﬁ es the content of the data portion of a beacon packet.

0 ~ 159 characters

−

CALIBRAT CAL

Sends a space/mark square wave (50/50 ratio). Enter Q to

exit Calibrate mode and restore the Command mode.

−−

CHECK CH

Speciﬁ es the interval from signal drop-out until execution of

disconnection. The unit of the parameter is 10 seconds.

0 ~ 250 30

CONMODE CONM

With NOMODE set to OFF, causes the TNC to automatically

enter Converse or Transparent mode when connection is

completed.

C/ T C

CONNECT C

Sends a connect request. Call1 is the callsign of the station

to be connected to. Call2 to call9 are callsigns of stations to

be digipeated through.

Call1 (VIA call2,

call3, ... call9)

−

CONOK CONO

When ON, accepts a connect request and returns a UA

packet. When OFF, rejects a connect request and returns a

DM packet.

ON/ OFF ON

CONSTAMP CONS

When ON, displays the current date and time when

connection is completed. The correct date and time must be

set using DAYTIME.

ON/ OFF OFF

CONVERSE

CONV

or K

Causes the TNC to enter Converse mode. Press [Ctrl]+[C] to

restore the Command mode.

−−

CPACTIME CP

When ON and in Converse mode, sends a packet at intervals

of the period determined by PACTIME.

ON/ OFF OFF

CR CR

When ON, appends a carriage return (CR) to all packets to

be sent.

ON/ OFF ON

DAYSTAMP DAYS

When ON, pressing [Ctrl]+[T] in Converse mode causes the

TNC to send date data in addition to time data.

ON/ OFF OFF

DAYTIME DA

Sets the current date and time. Enter YYMMDDhhmmss.

Sets 00 as the second if entry of the second is omitted.

−−

DAYUSA DAYU

When ON, displays the date like MM/DD/YY. When OFF,

displays the date like DD-MM-YY.

ON/ OFF ON

DIGIPEAT DIG When ON, allows the TNC to function as a digipeater. ON/ OFF ON

DISCONNE D Sends a disconnect request.

−−

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TM-D710GE Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TM-D710GE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info