45743
21
Zoom out
Zoom in
Vorherige Seite
1/150
Nächste Seite
13
4 GETTING ACQUAINTED
REAR PANEL
EXT. SP2
8
PANELCOM
ANT 2 ANT 1
ANT
144
AT
ANT 1.2G
DC
13.8V
ANT
430
EXT. SP1
8
ACC2
EXT. CONT
REMOTE
HF
RX ANT
PADDLE
KEY
GND
2 1
1
9
10 12 13 14 1511
32 4 5 86
7
q ANT 1 and ANT 2 connectors
Connect your primary HF/ 50 MHz antenna to ANT 1. If
you are using 2 antennas for the HF/ 50 MHz band,
connect the secondary antenna to the ANT 2 connector.
w GND post
Connect a heavy gauge wire or copper strap between
the ground post and the nearest earth ground {page 1}.
e KEY and PADDLE jacks
The PADDLE jack mates with a 6.3 mm (1/4")
3-conductor plug for connecting a keyer paddle to the
internal electronic keyer. The KEY jack mates with a
3.5 mm (1/8") 2-conductor plug for connecting an
external key for CW operation. Read “Keys for CW
(PANEL and KEY)” {page 3} before using these jacks.
r AT connector
Mates with the connector on the cable supplied with
the external antenna tuner. Refer to the instruction
manual supplied with the tuner for more information.
t ANT 144
Connect your 144 MHz band antenna to this connector.
y ANT 430
Connect your 430/ 440 MHz band antenna to this
connector.
u ANT 1.2G (TS-2000/ TS-B2000 Optional)
Connect your 1.2 GHz band antenna to this connector.
i DC 13.8V power input connector
Connect a 13.8 V DC power source to this connector
{page 2}. Use the cable supplied with the regulated
DC power supply.
o COM connector
Mates with a 9-pin female RS-232C connector for
connecting a computer via one of its serial
communication ports {page 93}. Also used with the
Quick Data Transfer function {page 93}.
!0 PANEL connector
Connect a cable from the optional separate remote
panel (RC-2000) to this connector.
!1 EXT.SP1 and EXT.SP2 jacks
Mate with a 3.5 mm (1/8"), 2-conductor (mono) plugs
for connecting external speakers {pages 3, 78}.
!2 EXT.CONT connector
Connect your 50 MHz, 144 MHz, 430/ 440 MHz or
1.2 GHz linear amplifier control cable to this
connector {page 76}.
!3 ACC2 connector
Mates with a 13-pin male DIN connector for
connecting various accessory equipment, such as an
external TNC/ MCP or a RTTY terminal {page 94}.
!4 REMOTE connector
Mates with a 7-pin male DIN connector for connecting
an HF linear amplifier {page 76}. Do not connect
50 MHz, 144 MHz, 430/ 440 MHz, or 1.2 GHz linear
amplifier controls to this connector; use the
EXT.CONT connector instead.
!5 HF RX ANT connector
Connect a separate receive-only antenna for HF low
bands to this jack (RCA connector) {page 76}.
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kenwood TS-2000E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info