Bedienungsanleitung Kenwood TS-2000E (Seite 43 von 150) (Englisch)

45743

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

8 ENHANCED COMMUNICATIONS

FM CTCSS OPERATION

You may sometimes want to hear calls only from

specific persons. When using FM mode, the

Continuous Tone Coded Squelch System (CTCSS)

allows you to ignore (not hear) unwanted calls from

other persons who are using the same frequency. A

CTCSS tone is sub-audible and is selectable from

among the 38 standard tone frequencies. Select the

same CTCSS tone as the other stations in your

group. You will not hear calls from stations other than

those using the same CTCSS tone.

Note: CTCSS does not cause your conversation to be private. It

only relieves you from listening to unwanted conversations.

1 Press [A/B] to select VFO A or VFO B.

•“tA” or “tB” appears to show which VFO is

selected.

2 Select a band.

3 Select an operating frequency.

4 Press [FM/ AM/ NAR] to select FM mode.

• “FM” appears.

5 Turn the SQL control to adjust the squelch.

6 Press [6/ CTCSS/SEL] to switch the CTCSS

function ON (or OFF).

• “C T” appears when the function is ON.

7 Press [FUNC], [6/ CTCSS/SEL].

• The current CTCSS frequency appears. The

default CTCSS frequency is 88.5 Hz.

8 Turn the MULTI/ CH control to select the

appropriate CTCSS frequency.

• The selectable CTCSS frequencies are listed in

the following table.

9 Press [FUNC], [6/ CTCSS/SEL] to complete the

setting.

.oN

.qerF

)zH(

.oN

.qerF

)zH(

.oN

.qerF

)zH(

.oN

.qerF

)zH(

100.76114.79125.631138.291

209.17210.001223.141235.302

304.47315.301322.641337.012

400.77412.701424.151431.812

507.97519.011527.651537.522

605.28618.411622.261636.332

704.58718.811729.761738.142

805.88810.321828.371833.052

905.19913.721929.971

018.49028.131032.681

You will hear calls only when the selected tone is

received. To answer the call, press [SEND] or press

and hold Mic [PTT], then speak into the microphone.

Skip steps 7 and 8 if you have already programmed

the appropriate CTCSS frequency.

Note:

◆

When using split-frequency operation, select FM mode on both

VFOs to use CTCSS.

◆

Use Nos. 01 to 38 shown in the table above when selecting

CTCSS frequencies via Wireless Remote Control {page 82}.

◆

You can select a CTCSS frequency independent of a tone

frequency.

◆

You cannot use the CTCSS function with the Tone or DCS

functions.

CTCSS FREQ. ID SCAN

This function scans through all CTCSS frequencies to

identify the incoming CTCSS frequency on a received

signal. You may find this useful when you cannot

recall the CTCSS frequency that the other persons in

your group are using.

1 Press [FUNC], [6/ CTCSS/SEL].

• The current CTCSS frequency appears.

2 Press [SCAN/ SG.SEL] to activate the CTCSS

Freq. ID scan.

• “C T” blinks and every CTCSS tone frequency

is scanned. When the CTCSS frequency is

identified, the transceiver stops scanning and

the identified frequency is displayed.

• Press [SCAN/ SG.SEL] again to resume

scanning.

• Press [SCAN/ SG.SEL] to stop scanning while

the CTCSS tone frequency ID scan is active.

Note: Received signals are audible while scanning is in progress.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info