Bedienungsanleitung Kenwood TS-2000E (Seite 58 von 150) (Englisch)

45743

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

11 SPECIALIZED COMMUNICATIONS

PREPARATION

1 Connect the transceiver to your personal

computer (via an external TNC or MCP if desired).

• See “COMPUTER” {page 93} and “MCP AND

TNC” {page 95}.

2 Install an appropriate terminal program onto the

personal computer.

• A variety of freeware and shareware programs

can be obtained in various ways. Consult your

reference material or other “packeteers”.

3 Initiate the terminal program and set the following

parameters on the personal computer:

• Transfer rate (TNC/MCP <–> Computer):

9600 bps (default setting)

• Data length: 8 bit

• Stop bit: 1 bit

• Parity: Non-parity

• Flow control: Hardware

4 Press [A/B] to select VFO A or VFO B.

5 Access Menu No. 46 and select the main band or

the sub-band (default) as the data band.

• “TNC” appears on the data band.

• If you are using an external TNC or MCP,

access Menu No. 50E to make this selection.

The default is main band.

6 Access Menu No. 47 and select 1200 bps (default)

or 9600 bps as the transfer rate between TNCs.

• You must select the same transfer rate as the

target station.

• If you are using an external TNC or MCP,

access Menu No. 50F to make this selection.

The default is 1200 bps.

7 Select an operating frequency.

8 Press [LSB/ USB/ AUTO] or [FM/ AM/ NAR] to

select LSB, USB, or FM mode.

9 Access Menu No. 50A and select ON to activate

the DSP packet filter for the main transceiver.

10 Turn the HI/ SHIFT control to select the center

frequency of the packet mode. You can further

select either “NAR” (narrow) or “WID” (wide) for

the receiver filter width by turning the LO/ WIDTH

control.

ycneuqerFretneC edoMgnitarepO

zH000113KSP

zH0071)spb0021KSFA(tekcaP

zH0122)spb003KSFA(tekcaP

KSPKSP

Note:

◆

The packet (9600 bps) operation is not affected by the DSP

packet filter settings.

◆

The DSP packet filter works only on the main transceiver.

If you are using an external TNC or MCP, proceed

with the subsequent steps.

11 Following the instructions provided with your TNC

or MCP, enter the calibration mode so that you

can generate a mark condition.

• The MAIN band LED changes from green (RX)

to red (TX).

12 Access Menu No. 50B to select the appropriate AF

input level.

• Select a proper input level, so that the ALC

meter reflects within the ALC zone.

13 Exit the calibration mode.

• The MAIN band LED changes from red (TX) to

green (RX).

14 Access Menu No. 50C to select the appropriate

AF output level.

• You cannot use the AF control to make this

adjustment.

• If you have selected sub-band in step 5,

access Menu No. 50D instead.

The frequencies (measured in kHz) commonly used

for Packet are listed below:

adanaC/.A.S.U )acirfA/eporuE(1noigeRURA

0381~0081—

5363~02630063~0953

0017~0807—

05101~04101—

5.99041~5904121141~10141,99041~98041

01181~50181—

00112~0901202112~00112

98182~0218200392~00292,05182~02182

08705~00605—

090541~019441—

570144~579044520134~050034

DCD SENSE

You can also select the method for inhibiting the built-

in TNC from transmitting. Access Menu No. 48 and

select one of the two methods. The default is “TNC

BAND”.

TNC BAND:

The TNC does not transmit when signals are present

on the TNC (data) band.

MAIN&SUB:

The TNC does not transmit when signals are present

on the main transceiver or sub-receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 58

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info