Bedienungsanleitung Kenwood TS-2000E (Seite 62 von 150) (Englisch)

45743

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

11 SPECIALIZED COMMUNICATIONS

3 Press [LSB/ USB/ AUTO] or [CW/ FSK/ REV] to

select LSB, USB, or CW mode.

4 As the Satellite moves, fine tune to the changing

downlink (RX) frequency of the satellite using the

Tuning control (adjusting the Doppler effect).

• As you adjust the downlink (RX) frequency, the

Trace function automatically changes the uplink

frequency so that the sum of the two

frequencies is kept the same (Reverse Trace).

• If necessary, press [A=B / TRACE] to quit the

Trace function. “TRACE” disappears.

• The trace function can also change the uplink

(TX) frequency so that the difference between

the two frequencies is kept the same (Normal

Trace).

5 If you want to switch to the normal trace mode,

press [SPLIT / REV]. “ ” disappears.

6 To adjust the frequency on the sub-band display

(normally the uplink frequency) without tracing,

turn the RIT/ SUB control. To adjust it using the

trace function, press [A/B / M/S] to swap the main

band frequency and sub-band frequency then turn

the Tuning control or MULTI/ CH control. The

following table shows which control to use when

adjusting frequencies with tracing ON and OFF.

ECART /

RECART NO

ECART /

RECART FFO

gninuT lortnoc

)lamroN(

buSdnaniaMniaM

HC/ITLUM

)esraoC(lortnoc

buSdnaniaMniaM

BUS/TIR

lortnoc

buSbuS

STORING SATELLITE MEMORY CHANNELS

You can store all the above settings to one of 10

Satellite memory channels for the future operations.

1 Press [M.IN], then turn the MULTI/ CH control to

select a channel from 0 to 9.

2 Select your desired settings.

3 Press [M.IN] again to store the selection to the

memory channel. To quit, press [CLR].

Note: The Satellite Memory channel does not hold the frequency

adjustment values when the channel is changed. So, when you

change the channel number or switch the transceiver OFF, the

adjustment frequency values are cleared if they are not stored by

pressing [M.IN].

RECALLING A SATELLITE MEMORY CHANNEL

1 Press [VFO/M / VFO/CH].

• The MULTI/ CH LED lights.

2 Turn the MULTI/ CH control to select the desired

Satellite Memory channel.

3 Press [VFO/M / VFO/CH] to return to the

frequency adjustment mode.

SATELLITE CHANNEL NAME

You can name each Satellite Memory channel using a

maximum of 8 alpha-numeric characters. First, store

the settings to the Satellite Memory channel {above}.

To store the Satellite Channel name:

1 Press [M.IN] then turn the MULTI/ CH control to

select the Satellite Memory channel.

2 Press [DISP].

3 An entry cursor appears. Select a character by

turning MULTI/ CH control, then move the cursor

using [SUB] or [MAIN]. You can also use the

other methods to enter the characters. Refer to

page 63 for details.

4 Press [M.IN] to store the name to the Satellite

Memory channel. Press [CLR] to quit.

5 The stored Satellite Memory name appears on the

main dot-matrix display.

QUICK MEMORY IN SATELLITE MODE

While in the Satellite mode, only 1 Quick Memory

channel is available. It uses Satellite Memory

channel 9 to store the settings. To store the settings

to the Quick Memory in Satellite mode, press

QUICK MEMO [M.IN]. The settings are stored to

Satellite Memory channel 9.

To recall the Quick Memory, press

QUICK MEMO [MR] or select Satellite Memory

channel 9, using the MULTI/ CH control. Satellite

Memory channel 9 is recalled.

CHECKING THE UPLINK FREQUENCY

When you need to monitor the uplink (TX) frequency,

press [TF-SET]. Each time you press [TF-SET], the

uplink (TX) frequency and the downlink (RX)

frequency are swapped.

USING XIT/ RIT IN SATELLITE MODE

You can also use the RIT or XIT function while in the

Satellite mode. Press [RIT/ CW TUNE] or [XIT/ ALT]

to activate the function. When the RIT or XIT function

is ON, the sub-band frequency display shows the

current RIT or XIT offset frequency instead of the

operating frequency. To clear the RIT or XIT offset

frequency, press [CLEAR].

Note: You cannot activate both the RIT and XIT functions at the

same time in the Satellite mode.

CHANGING THE FREQUENCY BAND

If you need to change the uplink and/or downlink

frequency band, press [CTRL] to move the “ ” icon

to the frequency band that you want to change.

Then, press [+]/ [–] to select the band you want to

operate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info