Bedienungsanleitung Kenwood TS-2000E (Seite 68 von 150) (Englisch)

45743

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

13 MEMORY FEATURES

■ Memory Scroll

1 Press [M.IN] to enter Memory Scroll mode.

• The memory channel that was last selected

appears.

2 Turn the MULTI/ CH control, or press Mic [UP]/

[DWN] to step through the memory channels.

• You can also change channels by entering a

3-digit number, such as 012, using the

numeric keys, then pressing [ENT].

3 To exit Memory Scroll mode, press [CLR].

• The transceiver re-displays the memory

channel or VFO frequency that was

selected before you activated Memory

Scroll.

Note: Do not press [M.IN] again after entering Memory Scroll

mode. Pressing [M.IN] results in over-writing the current VFO

data to the memory channel you selected.

■ Temporary Frequency Changes

After retrieving frequencies and associated data in

Memory Recall mode, you can temporarily change

the data without overwriting the contents of the

memory channel.

1 Access Menu No. 06B and select ON.

• Skip this step when changing only the

associated data (not the frequency).

2 Recall a memory channel.

3 Change the frequencies and associated data.

• Use only the Tuning control to select a

frequency.

4 If necessary for future use, store the changed

data in another memory channel. Refer to

“Channel ➡ Channel Transfer” {page 61}.

Note: Memory channel data can also be changed while using

the TF-SET function.

MEMORY-VFO SPLIT OPERATION

Under “ENHANCED COMMUNICATIONS” {page 31},

you learned about split-frequency operation using two

VFOs. Recalling a split-frequency channel is another

way to perform split-frequency operation. If you

access Menu No. 06A and select ON, you can also

use a memory channel and a VFO together for this

operation, as follows:

• RX: Memory channel

TX: VFO A or VFO B

• RX: VFO A or VFO B

TX: Memory channel

To use a memory channel for receiving:

1 Access Menu No. 06A and select ON.

2 Press [A/B] to select the VFO that you will use for

transmitting.

•“tA” or “tB” appears to show which VFO is

selected.

3 Select the frequency for transmitting.

4 Recall a memory channel by pressing [VFO/M].

5 Turn the MULTI/ CH control to select a memory

channel to receive.

6 Press [SPLIT].

7 The VFO A frequency appears on the sub-display.

If you want to use the VFO B frequency to

transmit, press [SPLIT] again.

8 Press [SEND] or Mic [PTT] to transmit on the

frequency shown on the sub display.

9 Press [SPLIT] to exit the SPLIT operation.

• If Split operation is still selected using VFO A or

VFO B, press [SPLIT] again to exit Split

operation.

To use a memory channel for transmitting:

1 Access Menu No. 06A and select ON.

2 Recall a memory channel by pressing [VFO/M].

3 Turn the MULTI/ CH control to select a memory

channel to transmit.

4 Press [VFO/M] to return to VFO mode.

5 Press [SPLIT]. The other VFO frequency appears

on the sub display for transmission (Normal SPLIT

operation).

6 Press [SPLIT] again. The memory channel you

selected in step 3 appears on the sub-display for

transmission.

7 Press [SEND] or Mic [PTT] to transmit on the

frequency in the memory channel.

8 Press [SPLIT] to exit SPLIT operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info