Bedienungsanleitung Kenwood TS-2000E (Seite 107 von 150) (Englisch)

45743

107

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

TROUBLESHOOTING

Note:

◆

Record the date of purchase, serial number and dealer from

whom the transceiver was purchased.

◆

For your own information, retain a written record of any

maintenance performed on the transceiver.

◆

When claiming warranty service, please include a photocopy of

the bill of sale, or other proof-of-purchase showing the date of

sale.

CLEANING

The keys, controls and case of the transceiver are

likely to become soiled after extended use. Remove

the controls from the transceiver and clean them with

a neutral detergent and warm water. Use a neutral

detergent (no strong chemicals) and a damp cloth to

clean the case.

LITHIUM BATTERY

This transceiver uses an EEPROM to store memory

channel data, menu configurations and all necessary

operation parameters. So, you never have to worry

about replacing batteries to operate the transceiver.

However, the transceiver’s built-in TNC requires a

lithium battery (CR-2032) to store the TNC data.

Battery lifetime varies, but under normal operating

conditions, it should last for approximately 5 years.

If you find that the TNC no longer stores the TNC

parameters, contact an authorized KENWOOD

service center for replacing the lithium battery.

DEMONSTRATION MODE

The transceiver can be configured to enter the

demonstration mode for display purposes. To enter

the demonstration mode:

1 Switch the transceiver OFF.

2 Press [FUNC]+[ ] to switch the transceiver ON.

• On the dot-matrix display windows, you will see

a few killer whales jump across the display.

You will also notice the display brightness

changes and LEDs turn ON and OFF

automatically.

• If you operate the transceiver while in the

demonstration mode, the demonstration is

temporarily paused. But, if no operation is

performed for more than 10 seconds, the

demonstration starts again.

3 To exit the demonstration mode, first turn the

transceiver OFF, then press [FUNC]+[ ] to turn

the transceiver ON.

Note: You cannot exit the demonstration mode by simply switching

the transceiver OFF or performing a full reset {page 92}. You must

switch the transceiver OFF then press [FUNC]+[ ] to turn the

transceiver ON in order to exit the demonstration mode.

GENERAL INFORMATION

Your transceiver has been factory aligned and tested

to specification before shipment. Under normal

circumstances, the transceiver will operate in

accordance with these operating instructions. All

adjustable trimmers, coils and resistors in the

transceiver were preset at the factory. They should

only be readjusted by a qualified technician who is

familiar with this transceiver and has the necessary

test equipment. Attempting service or alignment

without factory authorization can void the transceiver

warranty.

When operated properly, the transceiver will provide

years of service and enjoyment without requiring

further realignment. The information in this section

gives some general service procedures requiring little

or no test equipment.

SERVICE

If it is ever necessary to return the equipment to your

dealer or service center for repair, pack the

transceiver in its original box and packing material.

Include a full description of the problems

experienced. Include both your telephone number

and fax number (if available) along with your name

and address in case the service technician needs to

call for further explanation while investigating your

problem. Don’t return accessory items unless you

feel they are directly related to the service problem.

You may return your transceiver for service to the

authorized KENWOOD dealer from whom you

purchased it or any authorized KENWOOD service

center. A copy of the service report will be returned

with the transceiver. Please do not send

subassemblies or printed circuit boards. Send the

complete transceiver.

Tag all returned items with your name and call sign

for identification. Please mention the model and

serial number of the transceiver in any

communication regarding the problem.

SERVICE NOTE

If you desire to correspond on a technical or

operational problem, please make your note short,

complete, and to the point. Help us help you by

providing the following:

1 Model and serial number of equipment.

2 Question or problem you are having.

3 Other equipment in your station pertaining to the

problem.

4 Meter readings.

5 Other related information (Menu setup, mode,

frequency, key sequence to induce malfunction,

etc.).

DO NOT PACK THE EQUIPMENT IN CRUSHED

NEWSPAPERS FOR SHIPMENT! EXTENSIVE DAMAGE MAY

RESULT DURING ROUGH HANDLING OR SHIPPING.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-2000E Seite 107

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info