Bedienungsanleitung Kenwood TS-480SAT (Seite 12 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

1 INSTALLATION

ANTENNA CONNECTION

An antenna system consists of an antenna, feed line, and ground. The transceiver can give excellent results if the

antenna system and its installation are given careful attention. Use a properly adjusted 50 Ω antenna of good

quality, a high-quality 50 Ω coaxial cable, and first-quality connectors. All connections must be clean and tight.

After making the connections, match the impedance of the coaxial cable and antenna so that the SWR is 1.5:1 or

less. High SWR will cause the transmit output to drop and may lead to radio frequency interference to consumer

products such as stereo receivers and televisions. You may even interfere with your own transceiver. Reports

that your signal is distorted could indicate that your antenna system is not efficiently radiating the transceiver’s

power.

Connect your primary HF/ 50 MHz antenna feed line to ANT 1 on the rear of the transceiver. If you are using two

HF/ 50 MHz antennas, connect the secondary antenna to ANT 2. Refer to page 16 for the location of the antenna

connectors.

Note:

◆

Transmitting without connecting an antenna or other matched load may damage the transceiver. Always connect the antenna to the

transceiver before transmitting.

◆

All fixed stations should be equipped with a lightning arrester to reduce the risk of fire, electric shock, and transceiver damage.

◆

The transceiver’s protection circuit will activate when the SWR is greater than 2.5:1; however, do not rely on protection to compensate for a

poorly functioning antenna system.

GROUND CONNECTION

At the minimum, a good DC ground is required to prevent such dangers as electric shock. For superior

communications results, a good RF ground is required against which the antenna system can operate. Both of

these conditions can be met by providing a good earth ground for your station. Bury one or more ground rods or

a large copper plate under the ground, then connect this to the transceiver GND terminal. Use heavy gauge wire

or a copper strap, cut as short as possible, for this connection. Do not use a gas pipe, an electrical conduit, or a

plastic water pipe as a ground.

LIGHTNING PROTECTION

Even in areas where lightning storms are less common, there are usually a limited number of storms each year.

Consider carefully how to protect your equipment and home from lightning. The installation of a lightning arrestor

is a start, but there is more that you can do. For example, terminate your antenna system transmission lines at an

entry panel that you install outside your home. Ground this entry panel to a good outside ground, then connect

the appropriate feed lines between the entry panel and your transceiver. When a lightning storm occurs,

disconnecting the feed lines from your transceiver will ensure additional protection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-480SAT Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info