Bedienungsanleitung Kenwood TS-480SAT (Seite 42 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

COMMUNICATING AIDS

RECEPTION

SELECTING YOUR FREQUENCY

In addition to turning the Tuning control or pressing

Mic [UP]/ [DWN], there are several other ways to

select your frequency. This section describes

additional methods of frequency selection that may

save you time and effort.

■ Direct Frequency Entry

When the desired frequency is far removed from

the current frequency, directly entering a

frequency from the numeric keypad is usually the

fastest method.

1 Press [ENT].

•“ - - . - - - . - - ” appears.

2 Press the numeric keys ([0] to [9]) to enter

your desired frequency.

• Pressing [ENT] at any time fills the

remaining digits (the digits you did not

enter) with 0 and completes the entry.

To select 1.85 MHz for example, press

[ENT], [0], [1], [8], [5], then press [ENT] to

complete the input (6 key strokes).

• Pressing [MTR/ CLR] before pressing

[ENT] cancels the entry and restores the

current VFO frequency.

Note:

◆

You can enter a frequency in the range of 30.00 kHz to

59.999.99 MHz. Refer to the specifications for the

available frequency range.

◆

Attempting to enter a frequency that is outside the

selectable frequency range causes an alarm to sound.

The entered frequency is rejected.

◆

When the entered frequency does not meet the current

VFO frequency step size requirement, the nearest

available frequency is automatically selected after the

entered frequency is changed.

◆

When the 10 Hz digit (last displayed digit) is entered, the

digit 0 is automatically entered for the 1 Hz digit, and

frequency entry is completed. The 1 Hz digit is not

displayed.

◆

When an entered frequency is accepted, RIT or XIT will be

switched OFF, but the RIT or XIT offset frequency is not

cleared.

■ Using the MHz key

Pressing [ ]/ [ ] on the Remote Control panel

changes Amateur bands. You can also use the

MULTI control to change the operating frequency

in steps of 1 MHz.

1 Press [MHz].

• “MHz” appears.

2 Turn the MULTI control.

• Clockwise increases the frequency and

counter-clockwise decreases the frequency.

3 Press [MHz] again to exit.

•“MHz” disappears.

If you prefer to change the frequency in steps of

100 kHz or 500 kHz rather than 1 MHz, press

[MHz] (1 s), then turn the MULTI control to select

100 kHz, 500 kHz, or 1 MHz.

Note:

Even if 100 kHz or 500 kHz is assigned for the

[MHz]

key,

“MHz” appears on the display.

■ Quick QSY

To move up or down the frequency quickly, use the

MULTI control. Turning this control changes the

operating frequency in steps of 5 kHz for SSB/

CW/ AM/ FSK and 10 kHz for FM.

• If you want to change the default frequency

step size, press [FINE/ STEP] (1 s). Turn the

MULTI control to select 5 kHz, 6.25 kHz, 10

kHz, 12.5 kHz, 15 kHz, 20 kHz, 25 kHz, 30

kHz, 50 kHz or 100 kHz for FM/ AM, and 500

Hz, 1 kHz, 2.5 kHz, 5 kHz, or 10 kHz for the

other modes. The default frequency step size

is 5 kHz for SSB/ CW/ FSK/ AM and 10 kHz for

FM.

• When changing the operating frequency by

using the MULTI control, frequencies are

rounded such that new frequencies are

multiples of the frequency step size. To disable

this function, access Menu No. 05 and select

“oFF” (default is ON).

•Within the AM broadcast band, the step size

automatically defaults to the frequency step

value in Menu No. 06. This frequency step

size can be switched between 9 kHz (all E-

types: “on”) and 5 kHz (K-type: “oFF”) via Menu

No. 06.

Note:

The programmed frequency step size for the

MULTI

control is stored independently for the HF and 50 MHz bands.

You can also set a different frequency step size for SSB/ CW/

FSK, AM and FM modes.

■ Configuring the Tuning Control as MULTI control

(FM)

In FM mode, you can configure the Tuning control

to change the frequency as same as the MULTI

control. Access Menu No. 04 and select “on”

(default is OFF). As you turn the Tuning control,

the frequency changes as same as turning the

MULTI control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-480SAT Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info