Bedienungsanleitung Kenwood TS-480SAT (Seite 48 von 104) (Englisch)

511243

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

8 COMMUNICATING AIDS

BUG KEY FUNCTION

The built-in electronic keyer also can be used as a

semi-automatic key. Semi-automatic keys are also

known as “Bugs”. When this function is ON, dots are

generated in the normal manner by the electronic

keyer. Dashes, however, are manually generated by

the operator by holding the keyer paddle closed for

the appropriate length of time.

To switch this function ON, access Menu No. 37 and

select “on”. The default is OFF.

Note:

When the Bug Key function is ON, CW Message Memory

(see below) cannot be used.

CW MESSAGE MEMORY

This transceiver has 3 memory channels for storing

CW messages. Each memory channel can store

approximately 50 characters (equivalent of 250 dots).

These memory channels are ideal for storing contest

exchanges that you want to send repeatedly. Stored

messages can be played back to check message

content or for transmitting.

The electronic keyer has a function that allows you

to interrupt playback and manually inject your own

keying. To switch this function ON, access Menu

No. 33 and select “on”. The default is OFF.

The electronic keyer can also repeatedly play back

the message that you stored. To switch this function

ON, access Menu No. 31 and select “on”. The

default is OFF.

For repetitive message playback, you can change

the interval between each series of messages.

Use Menu No. 32 and select the time in the range

of 0 to 60 seconds in steps of 1 second {page 41}.

Note:

◆

This function cannot be used when the Bug Key function is

ON.

◆

Operating the keyer paddle with Menu No. 33 OFF cancels

message playback. Even if message playback does not stop

because of your keying start timing, you can cancel playback

by pressing

[MTR/ CLR]

■ Storing CW Messages

1 Press [MODE] until you select CW mode.

• “CW” or “CWR” appears.

2 If VOX is ON, press [VOX/ 8].

• “VOX” disappears {page 39}.

3 Press [CH1/ 1/ REC] (1 s), [CH2/ 2/ REC]

(1 s) or [CH3/ 3/ REC] (1 s) to select a memory

channel to be recorded.

• If the Constant Recording is ON (Menu No.

30), you cannot store a message to CH3

{page 69}.

4 Begin sending using the keyer paddle.

• The message you send is stored in memory.

5 To complete the message storage, press

[MTR/ CLR] to stop.

• When the memory becomes full, recording

automatically stops.

Note:

◆

If you do not operate the keyer paddle after starting to record

a message, a pause is stored in the channel.

◆

When the optional VGS-1 is installed and the Constant

Recording function is working, CH3 cannot be used.

■ Checking CW Messages without Transmitting

1 Press [MODE] until you select CW mode.

• “CW” or “CWR” appears.

2 If VOX is ON, press [VOX/ 8] to switch it OFF.

3 Press [CH1/ 1/ REC], [CH2/ 2/ REC] or

[CH3/ 3/ REC] to select the channel to be

played back.

• The message is played back.

•To play back the messages stored in the

other channels in sequence, press the

corresponding channel keys during

playback. Up to 3 channels can be queued

at the same time.

• While playing back the messages, you can

also adjust the keyer speed by pressing

[KEY/ 6/ DELAY] and turning the MULTI

control.

•To interrupt playback, press [MTR/ CLR].

■ Transmitting CW Messages

Messages can be transmitted using Semi Break-

in/ Full Break-in or manual TX/ RX switching.

1 Press [MODE] until “CW” or “CWR” appears.

2 To use Semi Break-in/ Full Break-in, press

[VOX/ 8].

• “VOX” appears.

3 Press [CH1/ 1/ REC], [CH2/ 2/ REC] or

[CH3/ 3/ REC] to select the channel to be

played back.

• The message is played back and

transmitted automatically.

•To transmit the messages stored in the

other channels in sequence, press the

corresponding channel keys during

playback. Up to 3 channels can be queued

at the same time.

• While playing back the messages, you can

also adjust the keyer speed by pressing

[KEY/ 6/ DELAY] and turning the MULTI

control.

•To interrupt transmission, press [MTR/ CLR].

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-480SAT Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-480SAT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info