Bedienungsanleitung Kenwood TS-590SG (Seite 10 von 96) (Englisch)

606692

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

1 INSTALLATION

UTILIZING THE BAIL

This transceiver is equipped with a bail so that you

can angle the transceiver. The bail is located on the

bottom of the transceiver. Pull the bail forward to the

limit as shown.

REPLACING FUSES

The following fuses are used in the TS-590SG

transceiver. If a fuse blows, determine the cause

then correct the problem. Only after the problem

has been resolved, replace the blown fuse with a

new one with the speciﬁ ed ratings. If newly installed

fuses continue to blow, disconnect the power plug and

contact a KENWOOD service center or your dealer for

assistance.

Fuse Location Fuse Current Rating

TS-590SG Transceiver

4 A

(for external

antenna tuner)

Supplied DC power cable 25 A

Fuse (4 A)

Fuse (25 A)

ACCESSORY CONNECTIONS

FRONT PANEL

■ Headphones (PHONES)

Connect monaural or stereo headphones with a

4 to 32  (normal 8 ) impedance. This jack

accepts a 6.3 mm (1/4") diameter, 2-conductor

(mono) or 3-conductor (stereo) plug. After

connecting the headphones, you will hear no

sound from the internal (or optional external)

Speaker/Microphone (MIC).

Note: Using a high impedance headphone set causes the

volume to be louder.

■ Microphone (MIC)

Connect a microphone with a 250 to 600 

impedance. Fully insert the connector, then

screw the retaining ring clockwise until secure.

Compatible microphones include the MC-43S,

MC-47, MC-52DM, MC-60A, MC-80, MC-85, and

MC-90.

Note: Do not use the MC-44, MC-44DM, MC-45, MC-45E,

MC-45DM, MC-45DME, or MC-53DM microphones.

REAR PANEL

■ External Speaker (EXT.SP)

On the rear panel of the transceiver, there is an

external speaker jack. If an external speaker is

connected to EXP.SP, the transceiver internal

speaker will mute. Use only external speakers with

an impedance of 4 to 8  (8  nominal). This jack

accepts only 3.5 mm (1/8") diameter, 2-conductor

(mono) plugs.

Do not connect headphones to this jack. The high audio

output of this jack could damage your hearing.

■ Keys for CW (PADDLE and KEY)

For CW operation while using the internal

electronic keyer, connect a keyer paddle to the

PADDLE jack.

For CW operation without using the internal

electronic keyer, connect a straight key,

semi-automatic key (bug), electronic keyer,

or the CW keyed output from a Multi mode

Communications Processor (MCP) to the KEY jack.

The PADDLE and KEY jacks mate with a 6.3 mm

(1/4") 3-conductor plug and a 3.5 mm (1/8")

2-conductor plug, respectively. External electronic

keyers or MCPs must use positive keying to be

compatible with this transceiver. Use a shielded

cable between the key and the transceiver.

Note: Due to the functionality of the internal electronic

keyer, you may ﬁ nd it unnecessary to connect both a paddle

and another type of keyer unless you want to use a

PC-based keyer for CW. Read the “ELECTRONIC KEYER”

section {page 34} to become familiar with the internal keyer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-590SG Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-590SG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info