Bedienungsanleitung Kenwood TS-590SG (Seite 33 von 96) (Englisch)

606692

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

ENHANCED COMMUNICATIONS 6

frequency. You will soon learn the rhythm of the

DX station and the pileup. The more proﬁ cient you

become at using this function, the more DX stations

you will contact.

Note:

◆ TF-SET is disabled while transmitting.

◆ You can change the transmission frequency even when the

Frequency lock function is ON.

◆ An RIT offset frequency is not added; however, an XIT offset

frequency is added to the transmit frequency during TF-SET.

◆ The TF-SET function does not operate in Simplex mode.

However, when the XIT function is ON and the RIT function

is OFF, the TF-SET function will operate in Simplex mode. In

this situation, you can set the XIT frequency while operating

TF-SET by rotating the Tuning knob or pressing the MIC [UP]

/ MIC [DOWN] keys.

SHIFTABLE RX FREQUENCY DURING SPLIT

TRANSMISSION

As the factory default setting, when rotating the Tuning

knob during split transmission, the transmit frequency

will change. By following the procedures below, when

rotating the Tuning knob during split transmission, you

can change the receive frequency.

1 Press [MENU], then press [Q-M.IN]/ [Q-MR] or

turn the MULTI/CH control to select Menu No. 20.

2 Press [M.IN]/ [SCAN (SG.SEL)] to select “on”

3 Press [MENU] to exit Menu mode.

• When you switch the transceiver ON while this

function is set to ON, the decimal point at the

right end digit of the main display ﬂ ashes for

approximately 2 seconds after the Power On

message is displayed.

FM REPEATER OPERATION

Most Amateur radio voice repeaters use a separate

reception and transmission frequency. The

transmission frequency may be higher or lower than

the reception frequency. In addition, some repeaters

may require the transceiver to transmit a subtone

before the repeater can be used.

Compared to simplex communication, you can

usually transmit over much greater distances by

using a repeater. Repeaters are typically located

on a mountain top or other elevated location. Often

they operate at higher ERP (Effective Radiated

Power) than a typical station. This combination of

elevation and high ERP allows communications over

considerable distances.

HF/ 6 m band repeaters usually operate in the

29 MHz FM sub-band and 51-54 MHz band. This

special service combines the advantages of FM

operation, good ﬁ delity with noise and interference

immunity, with the excitement of HF DX (long

distance) communications. Even on a quiet day,

10 m FM provides reliable around-town

communications with the potential for sudden DX from

across the country or around the world.

Note:

◆ When programming 2 separate frequencies using 2 VFOs,

be sure to select FM mode on both VFOs.

◆ When operating through a repeater, over deviation caused

by speaking too loudly into the microphone can cause your

signal to “talk-off” (break up) through the repeater.

29.520 MHz

88.5 Hz

29.520 MHz

88.5 Hz

29.620 MHz

1 Press [A/B (A=B)] to select VFO A or VFO B.

• “ ” or “ ” appears to show which VFO is

selected.

2 Turn the Tuning control or the MULTI/CH control to

select the reception frequency.

3 Press [FM/AM (FM-N)] to select FM mode.

4 Press and hold [A/B (A=B)] to duplicate the

frequencies and other data to the other VFO.

5 Turn the Tuning control or the MULTI/CH control to

select the transmission frequency.

6 Press [AGC/T (SEL] to turn the Tone function ON if

the repeater requires a subtone.

• “

” appears.

• Refer to “Selecting a Tone Frequency” for more

details on the subtone {page 26}.

• To quit the Subtone function, press [AGC/T (SEL)]

twice.

7 Press [SPLIT].

• “ ” appears.

8 Press [A/B (A=B)] to return to the original

reception frequency.

9 Press Mic [PTT] to transmit.

• The VFO changes to the other VFO to transmit.

• Each time you press [A/B (A=B)], the reception

and transmission frequencies are swapped.

10 Press [SPLIT] to quit split-frequency operation.

• “

” disappears.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-590SG Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-590SG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info