Bedienungsanleitung Kenwood TS-890S (Seite 14 von 196) (Englisch)

683161

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

Torque Adjustment with Tuning Control

The Tuning control allows the rotational torque (weight) to be

adjusted according to the user’s preference. With the ring at the

base of the Tuning control fixed, turning the Tuning control to the

right increases the rotational torque, while turning to the left

decreases it.

Ring

Connection of Accessories (Front Panel)

■

Headphones (PHONES)

Monaural and stereo headphones (4 to 32 Ω, standard: 8 Ω/plug:

Φ6.3 mm) can be used with this transceiver.

When headphones are connected, sound will not be output from

the built-in speakers (or optional external speakers). The following

optional headphones are compatible with this transceiver.

●HS-5 ●HS-6

●

The volume may be louder for headphones with a higher

impedance.

●

The audio output is monaural even when stereo

headphones are connected.

■

Paddle (PADDLE)

For CW operation using the built-in electronic keyer, connect a

keyer paddle to the PADDLE jack. A Φ6.3 mm three-pronged plug

is used for the paddle. Also, a straight key can be connected to the

PADDLE jack. In this case, change the setting of Menu [5-00] to

“Straight Key”. (Refer to Chapter 3 for details on menu operation.)

■

USB Flash Drive/ USB Keyboard ( )

For connecting a commercially available USB flash drive or USB

keyboard.

Plug the USB flash drive or USB keyboard firmly into the (USB-A)

connector.

●

Do not remove the USB flash drive while reading or

writing files or while the USB flash drive is being

accessed by this transceiver. Also, do not turn off the

power of this transceiver.

●

Always remove the USB flash drive after executing

“Safely Removing the USB Flash Drive” (11-6) to

prevent data in the USB flash drive from being damaged.

(USB/File Management Menu “Safe Removal of USB

Flash Drive”)

●

A USB flash drive or USB keyboard can be connected to

the connector on the front panel and rear panel respectively.

■

Microphone (MIC)

Microphones with an impedance of 250 Ω to 600 Ω can be used.

Insert the microphone plug fully into the MIC connector of this

transceiver and tighten it firmly using the fastening ring.

The following microphones (sold separately) are compatible with

this transceiver.

●MC-43S ● MC-60A ● MC-90 ●MC-47

The following microphones are not compatible with this transceiver.

●MC-44 ●MC-44DM ●MC-45 ●MC-45DM

●

Production of the MC-47 microphone has been

discontinued.

Microphone Connector

(View from Front Panel)

8V (10mA max)

GND (MIC)

GND (STBY)

DOWN

PTT

MIC

Microphone

(Optional or Commercially

Available)

USB Flash Drive (Commercially

Available) or USB Keyboard

(Commercially Available)

Front Panel

Paddle (Commercially Available)

Straight Key (Commercially Available)

Headphones

(Optional or Commercially

Available)

1 INSTALLATION AND CONNECTION

1-2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info