Bedienungsanleitung Kenwood TS-890S (Seite 17 von 196) (Englisch)

683161

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

■

Configuration for Switching the RX Bandwidth

Configure the setting as follows to switch the RX bandwidth by cutting off the high or low frequencies within the frequency range of 0 Hz

to 5000 Hz even in the SSB-DATA mode, in the same way as in SSB mode, during operations such as FT8.

* Refer to “Configuring the Behavior of the HI/SHIFT and LO/WIDTH Controls (SSB/SSB-DATA Only)” (6-3).

Configure in Menu [6-12] “Filter Control in SSB-DATA Mode (High/Low and Shift/Width)”. Select “High & Low Cut”.

●

USB cable and RS-232C straight cable are not supplied with this transceiver. Please purchase commercially available cables.

●

Delays may occur when using USB audio, and there may also be audio interruptions depending on the performance and load

of the PC.

●

Place this transceiver far enough from the PC so that noise will not be picked up.

●

For data communication software settings, refer to the instruction manual or Help file of the software in use.

Virtual COM Port

PC command control using the virtual COM port and USB keying control using the RTS/DTR signal of the virtual COM port can be

performed by connecting this transceiver and the PC using a USB cable.

•

To use the virtual COM port, Windows 10, Windows 8.1 or Windows 7 is required. (as of January, 2019)

•

Install the virtual COM port driver on the PC before connecting the USB cable. Download the driver from the following URL.

http://www.kenwood.com/i/products/info/amateur/software_download.html

•

There are 2 types of virtual COM port on this transceiver, namely virtual COM (Standard) port and virtual COM (Enhanced) port.

•

The COM port numbers of the virtual COM (Standard) port and virtual COM (Enhanced) port on the PC can be checked using the

following way.

•

Open the Device Manager in Windows.

•

Connect this transceiver and the PC using a USB cable. The following 2 COM ports are displayed in “Ports (COM & LPT)” in the

Device Manager.

“Silicon Labs CP210x USB to UART Bridge (COM x)”

“Silicon Labs CP210x USB to UART Bridge (COM y)”

x and y are numbers. The numbers vary depending on the PC environment used. The following is the display example of the virtual

COM ports on this transceiver assigned to COM3 and COM4.

•

Double-click on these in the Device Manager to display the respective Properties windows.

•

Select the “Details” tab and then select “Location paths” from the Property drop-down menu.

•

Move the mouse cursor to the top line displayed in the “Value” column and check the number in the parenthesis on the right end

of the character string.

The port displayed with the number (1) is the virtual COM (Standard) port of this transceiver.

The port displayed with the number (2) is the virtual COM (Enhanced) port of this transceiver.

The following is the display example of the Properties window of each COM port when the virtual COM (Standard) port and the virtual

COM (Enhanced) port are assigned to COM3 and COM4 respectively.

INSTALLATION AND CONNECTION 1

1-5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info