Bedienungsanleitung Kenwood TS-890S (Seite 95 von 196) (Englisch)

683161

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

Configuring the NR1 Effect Level

1 Press [NR] to select Noise Reduction 1.

2 Press and hold [NR] to display the Noise Reduction

1 effect level configuration screen.

3 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control

to change the level of effect.

Setting Value 1 to 5 (default) to 10 (1 step)

•

For NR1, configuring to a larger value reduces the noise

further. However, as the impact on the RX audio also gets

stronger if the effect level is excessively high, adjust it to an

appropriate level.

4 Press and hold [NR] or press [ESC] to end the

process.

Configuring the NR2 Correlation Time

1 Press [NR] to select Noise Reduction 2.

2 Press and hold [NR] to display the NR2 Time

Constant configuration screen.

3 Press F4 [–]/ F5 [+] or turn the [MULTI/CH] control

to change the correlation time.

Setting Value 2 to 20 (default) [ms] (2-step)

•

As the optimal correlation time varies with the RX signal and

noise type when NR2 is used, configure the correlation time

while receiving the signals.

4 Press and hold [NR] or press [ESC] to end the

process.

●

NR2 adjusts the correlation time for periodic signal

extraction. It is different from NR1, which adjusts the

effect level.

Beat Canceler

Beat canceler is capable of suppressing multiple periodic

interfering signals (beats) within the RX bandwidth through digital

processing at the AF level.

This function can be used in the SSB, AM and FM modes.

Turning ON/OFF Beat Canceler

Press [BC].

Pressing [BC] each time switches the beat canceler mode in

the following sequence: “Beat Canceler 1” → “Beat Canceler 2”

→ “OFF”.

•

When beat canceler 1 or beat canceler 2 is ON, <<

BC 1

or <<

BC 2

>> is displayed on the screen.

•

Beat canceler 1 suppresses weak beats and continuous

beats. Beat canceler 2 suppresses intermittent beats such

as CW signals.

●

Although the beat canceler suppresses the overall

auditory beat, the gain of the target signal cannot be

recovered using the AGC function. Thus, if the beat

signal is larger than the target signal, using a notch filter

activates the AGC function to enhance the clarity of the

target signal.

DSP Monitor

DSP monitor is a function for temporarily expanding the passband

width of the IF filter and AF filter via DSP in order to monitor the

signal condition of nearby frequencies such as when receiving a

specific frequency using a filter with a narrow passband width

during contesting.

Assigning DSP Monitor to PF Key

“PF A: Key

Assignment” to Menu [0-31] “Microphone UP: Key

Assignment”

Expanding the Passband Width Using DSP Monitor

Press and hold down the PF key that is assigned

with the DSP monitor function.

The passband width of the filter is expanded while the key is

held down.

●

During DSP monitoring, the audio peak filter is forcibly

turned OFF.

REJECTING INTERFERENCE 6

6-9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info