683161

Kenwood TS-890S Seite 163

163
Zoom out
Zoom in
Vorherige Seite
1/196
Nächste Seite
PC Control
The ARCP-890 radio control program, ARHP-890 radio host
program, ARUA-10 USB audio control program and PC
commands are used to control this transceiver or to enable the use
of a PC speaker or microphone.
•
This manual describes only the procedures for configuring the
baud rate of the COM/USB port used for PC control. For more
details on the necessary preparations and method of operation,
please refer to the descriptions of the respective program
software (Help text) and PC command list.
•
To control this transceiver via USB cable connection, download
the virtual COM port driver.
•
To output the RX audio from the PC speaker using the USB
audio function or transmit the audio input to the PC microphone,
download the ARUA-10 audio controller. (In principle, delay
occurs when USB audio is used. Make use of it for
communication where time lag does not constitute an issue.)
•
The abovementioned program, virtual COM port driver and PC
command list can be downloaded from the website below.
http://www.kenwood.com/i/products/info/amateur/
software_download.html
●
Make sure not to connect this transceiver and the PC
with the USB cable until the installation of the virtual COM
port driver downloaded from the above URL is
completed.
●
If this transceiver is connected to the PC without
installing the virtual COM port driver, a wrong driver that
is not compatible with this transceiver may be installed
and communication with the PC may not be established
properly. To prevent a wrong driver from being installed,
the virtual COM port driver must be installed before
connecting to the PC.
●
Before connecting this transceiver with a PC, make sure
to turn off the power of this transceiver.
●
The USB function of this transceiver complies with the
USB 2.0 standard. (USB audio complies with USB Audio
Class 1.0.)
Configuring the COM/USB (Rear Panel) Baud Rate
This is used to configure the baud rate of the COM/USB port used
for PC control.
Configure in Menu [7-00]
“Baud Rate (COM Port)”
(COM) or Menu [7-01] “Baud Rate (Virtual Standard
COM)” (USB)
COM
Setting Value
4800/ 9600 (default)/ 19200/ 38400/ 57600/
115200 [bps]
USB
Setting Value
9600/ 19200/ 38400/ 57600/ 115200 (default)
[bps]
●
To use the baud rate of 38400, 57600 or 115200 bps,
configure the baud rate of the RS-232C port of the PC
you are using to a high speed.
●
When using the ARCP-890, use a transfer rate that is as
fast as possible.
●
To display the bandscope at the normal speed during
remote control of this transceiver using the ARCP-890
and ARHP-890, it is necessary to use an even higher
baud rate. Connect a home LAN to the LAN connector
on the rear panel.
Configuring the USB Keyboard
A USB keyboard can be used by connecting it to the (USB-A) port
on the front or rear panel. It can be used to transmit or play back
the voice or message assigned to a function key or to enter and
transmit a text in the RTTY (FSK) or PSK mode.
When connected to this transceiver, the USB keyboard can be
used for text input. The behavior (key repeat) when a key on the
USB keyboard is pressed and held can also be configured.
Sending Message from the USB Keyboard
When this transceiver is configured as follows, a voice or message
can be sent out by pressing the corresponding function key on the
USB keyboard.
•
When message sending from the USB keyboard is ON
•
A voice or message has been assigned to a function key on the
USB keyboard
Configure in Menu [9-00] “Send Message by
Function Keys”
Setting Value Off/ On (default)
●
When 2 USB keyboards are connected, only the one that
is first connected to this transceiver is recognized.
●
Channels not registered with a message cannot be
selected.
●
Message in the CW, FSK or PSK mode is sent out
according to the settings of the channel in which the
message is registered.
●
While in the CW, FSK or PSK mode, a message can be
sent out when the RTTY communication screen is
displayed.
Selecting a USB Keyboard Language
Configure the type of USB keyboard (language or region) that is
connected to this transceiver.
Configure in Menu [9-01]
“Keyboard Language”
Setting Value
Japanese/ English(US) (default)/ English(UK)/
French/ French(Canadian)/ German/
Portuguese/ Portuguese(Brazilian)/ Spanish/
Spanish(Latin American)/ Italian
Configuring the Time for Activating Key Repeat
Configure the time interval before activating the key repeat
operation of the USB keyboard.
Configure in Menu [9-02]
“Repeat Delay Time”
Setting Value 1 to 2 (default) to 4 (1 step)
Configuring the Key Repeat Speed
Configure the key repeat speed of the USB keyboard.
Configure in Menu [9-03]
“Repeat Speed”
Setting Value 1 (default) to 32 (1 step)
OTHER FUNCTIONS 16
16-5
… 163 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kenwood TS-890S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kenwood TS-890S

Kenwood TS-890S Bedienungsanleitung - Deutsch - 196 seiten

Kenwood TS-890S Bedienungsanleitung - Holländisch - 196 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info