Bedienungsanleitung Kenwood TS-890S (Seite 175 von 196) (Englisch)

683161

175

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

Operation

The crossband repeater function uses 2 frequency bands to

receive and transmit signals. When a signal is received on one

band, it is retransmitted on the other band.

1 Select a transmission/reception VHF or UHF

frequency on the FM transceiver.

2 Confirm the PTT icon is visible on the crossband

repeater frequency on the FM transceiver.

3 Select the same frequency for the terminal

transceiver.

4 Select a HF/50 MHz frequency on the TS-890S

transceiver.

5 Adjust the squelch threshold level so that both the

TS-890S and FM transceivers mute.

6 On the TS-890S, press [MENU], then access

Advanced Menu [11] (PKS Polarity Reverse) and

[12] (TX Inhibit While Busy).

Select “On”.

•

When the TS-890S transceiver’s squelch opens, the FM

transceiver simultaneously retransmits the incoming audio

signal on the VHF or UHF frequency.

•

When the FM transceiver’s squelch opens, the TS-890S

transceiver retransmits the incoming audio signal on the HF/

50 MHz frequency.

8 Access Menu [7-07] (ACC2: Audio Input Level) and

[7-09] (ACC2: Audio Output Level) and adjust the

input/ output audio level.

9 To quit the FM repeater operation, disconnect the

interface cable between the transceivers, then

access Advanced Menu [11] and [12] on the

TS-890S transceiver and select “Off”.

Sky Command System II

Sky Command System II allows you to remotely control the

TS-890S transceiver from a separate location.

•

If you have more than 2 TH-D7A/ TH-D72(A/E)/ TM-D710/G(A/

E)/ TM-V71A + RC-D710/ TM-D700A transceivers, you can

perform Sky Command System II operation to remotely control

your TS-890S transceiver.

•

You will use one transceiver (TH-D7A, TH-D72(A/E)/ TM-D710/

G(A/E), TM-V71A + RC-D710, or TM-D700A) as a remote

control unit, called a “Commander”. The other VHF/ UHF

transceiver (TH-D7A, TH-D72(A/E)/ TM-D710/G(A/E), TM-

V71A + RC-D710, or TM-D700A) with the TS-890S transceiver

is called the “Transporter”. This TH-D7A, TH-D72(A/E)/ TM-

D710/G(A/E), TM-V71A + RC-D710, or TM-D700A transceiver

will function as an interface between the Commander (a remote

control unit) and the band of the TS-890S transceiver.

•

This system allows you, for example, to watch for and hunt DX

while washing your car, or to operate the HF transceiver while

relaxing in your car, living room, or patio, instead of actually

operating inside your shack.

●

Operation of Sky Command System II may not been

permitted in certain countries. Check your local laws

before operating.

Sky Command System II Diagram

Transporter

Response

Control Command

Audio

Commander

Response

Control Command

Audio

UHF Frequency

Audio

VHF Frequency

Preparation

Although you can use a TH-D7A, TH-D72(A/E)/ TM-D710/G(A/E),

TM-V71A + RC-D710, or TM-D700A transceiver as a

“Commander” (an external remote control unit), the following

procedure shows how to set up your TS-890S and TH-D7A, TH-

D72(A/E)/ TM-D710/G(A/E), TM-V71A + RC-D710, or TM-D700A

transceivers as a “Transporter” at a base station and the TH-

D72(A/E)/ TM-D710/G(A/E), TM-V71A + RC-D710, or TM-D700A

transceiver as a “Commander”.

OTHER FUNCTIONS 16

16-17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood TS-890S Seite 175

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood TS-890S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info