Bedienungsanleitung Kenwood VR-507 (Seite 9 von 52) (Englisch)

40361

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Make connections as shown m the followmg pages.

When connecting the related system components, be sure

to also refer to the Instruction manuals supplied with the

components you are connecting.

Do not connect the power cord to a wall outlet until all

connections are completed.

Notes

1. Be sure to Insert all connection cords securely. If their connections are

Imperfect, the sound may not be produced or noise may Interfere.

2. Be sure to remove the power cord from the AC outlet before pluggrng or

unpluggrnganyconnectioncords. Pluggrng/unpluggrngconnection cords

without disconnecting the power cord can cause malfunctions and may

damage the unit.

3. Do not connect power cords from components whose power consump-

tion IS larger than what IS indicated on the AC outlet at the rear of thus unit.

DTS disclaimer clause

DTS Digital SurroundTM IS a discrete 5.1 channel digital audio format

available on CD, LD, and DVD software which consequently cannot be

decoded and played back rnsrde most CD, LD, or DVD players. For this

reason, when DTS-encoded software IS played back through the analog

outputs of the CD, LD, or DVD player, excessrve norse will be exhibited.

To avord possible damage to the audio system, proper precautions

should be taken by the consumer if the analog outputs are connected

directly to an amplification system. To enjoy DTS Digital SurroundTM

playback, an external 5.1 channel DTS Digital SurroundTM decoder

system must be connected to the digital output (S/P DIF, AES/EBU, or

TosLInk) of the CD, LD or DVD player.

Analog connections

Audio connections are made usrng RCA pm cords. These cables transfer

stereo audio signal In an “analog” form. This means the audio signal

corresponds to the actual audio of two channels. These cables usually have

2 plugs each end, one red for the right channel and one white for the left

channel. These cables are usually packed together with the source unit, or

are available at your local electronrcs retailer.

input mode settings

CD/DVD, VIDE02, VIDEO3

and

DVD/Gch

Inputs each Include jacks

for digital audio input and analog audio Input.

You must select beforehand whrch type of input IS to be used for each

connected component.

The initial factory settings for audio srgnal playback (CD/DVD,

DVD16ch) and (VIDEOP, VIDEOI) are digital and analog respec-

tively.

To use the analog audio input for playback Instead (if, for example, you

have connected a VCR to the VIDEO2 or VIDEO3 input), you must set

the Input mode for the corresponding Input to the analog mode.

After completing connections and turning on the recerver, follow the

steps below.

INPUT SELECTOR

INPUT MODE

0 Use the INPUT SELECTOR knob to select CDIDVD, VIDEOZ,

VIDEO3 or DVD/Gch.

0 Press the INPUT MODE key.

Each press switches the settlng as follows:

In DTS play mode

c 0 D-AUTO

(digital Input, auto sound)

0 D-MANUAL

(digital input, manual sound)

In DVD16ch play mode

[

0 D-AUTO

(digital input, auto sound)

0 D-MANUAL

(digital input, manual sound)

@ 6ch INPT

(DVD/Gch input)

@ ANALOG

(analog Input, manual sound)

In modes other than DTS or DVD/6ch play mode

0 D-AUTO

(digital Input, auto sound)

@ D-MANUAL

(digital Input, manual sound)

0 ANALOG

(analog Input, manual sound)

Digital Input:

Select this setting to play digital signals from a DVD, CD, or LD player.

Analog Input:

Select thus setting to play analog signals from a cassette deck, VCR,

or record player.

Auto sound:

In the auto sound mode

(AUTO SOUND

indicator lights), the recerver

selects the listenrng mode automatically durrng playback to match the

type of input signal (Dolby Digital, PCM, DTS) and the speaker setting.

The initial factory setting IS auto sound on.

To keep the recerver set to the currently selected listenrng mode, use

the

INPUT MODE

key to select

“D-MANUAL”

(manual sound).

However, even when thus setting IS selected, there may be cases In

whrch the listening mode IS selected automatically to match a Dolby

Digital source srgnal depending on the combination of listening mode

and source srgnal.

If the INPUT MODE key IS pressed quickly, sound may not be

produced.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood VR-507 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info