Bedienungsanleitung Kenwood VR-6050 (Seite 15 von 44) (Englisch)

40359

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Setting up the system

Connecting the terminals

1 Strip coating. 2 Loosen.

3 Insert. 4 Secure.

1 Strip coating. 2 Push the lever.

3 Insert the cord. 4 Return the lever.

Connection of banana plugs (For the U.S.A. and Canada)

1 Secure. 2 Insert.

• Sound will not be heard if the speaker terminal is not fully secured.

• Never short circuit the + and – speaker cords.

• If the left and right speakers are connected inversely or the speaker

cords are connected with reversed polarity, the sound will be

unnatural with ambiguous acoustic imaging. Be sure to connect the

speakers correctly.

Speaker impedance

After confirming the speaker impedance indications printed on the

rear panel of the receiver, connect speakers with matching imped-

ance ratings. Using speakers with a rated impedance other than that

indicated on the rear panel of the receiver could result in malfunctions

or damage to the speakers or receiver.

Speaker placement

Front speakers : Place at the front left and right of the listening

position. Front speakers are required for all surround modes.

Center speaker : Place front and center. This speaker stabilizes the

sound image and helps recreate sound motion. Required for surround

playback.

Surround speakers : Place at the direct left and right, or slightly

behind, the listening position at even heights, approximately 1 meter

above the ears of the listeners. These speakers recreate sound

motion and atmosphere. Required for surround playback.

Subwoofer : Reproduces powerful deep bass sounds.

Surround back speaker : Place the speaker directly at the rear of the

listening position. The optimum position depends mainly on the room

condition.

• Although the ideal surround system consists of all the speakers

listed above, if you don't have a center speaker or a subwoofer, you

can divide those signals between the available speakers in the

speaker settings steps to obtain the best possible surround repro-

duction from the speakers you have available. *

Channel space switching

(Except for the U.S.A., Canada, U.K., and Australia)

The space between radio channels has been set to the one that

prevails in the area to which the system is shipped. However, if the

current channel space setting does not match the setting in the area

where the system is to be used, for instance when you move from

area 1 or area 2 shown in the following table or vice versa, proper

reception of AM/FM broadcasts cannot be expected. In this case,

change the channel space setting in accordance with your area by

referring to the following table.

Area

CHANNEL

Space Frequency

U.S.A., Canada and South FM: 100 kHz

American countries AM: 10 kHz

2 Other countries

FM: 50 kHz

AM: 9 kHz

50us

AM 9kHz

FM50kHz

75us

AM 10kHz

FM100kHz

DE-EMPHASIS

CHANNEL SPACE

DE-EMPHASIS

CHANNEL SPACE

50us

AM 9kHz

FM50kHz

75us

AM 10kHz

FM100kHz

Turn the power OFF by pressing the POWER key before moving the

switch level. Move switch lever to match your area with a small

screwdriver or other pointed tool, then turn the power on again.

Center speaker

Subwoofer

Front

speaker

Surround

speaker

Surround

back speaker

Listening

position

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood VR-6050 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info