Bedienungsanleitung Kenwood VRS6200 (Seite 7 von 40) (Englisch)

510822

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Input mode settings

DVD, VIDEO and GAME (FRONT AUX) inputs each include jacks for

digital audio input and analog audio input.

The initial factory settings for audio signal playback for DVD, VIDEO

and GAME (FRONT AUX) are full auto.

After completing connections and turning on the receiver, follow the

steps below.

Setting up the system

INPUT SELECTOR

INPUT MODE

1 Use the INPUT SELECTOR key (or input selector keys)

to select DVD, VIDEO or GAME (FRONT AUX).

2 Press the INPUT MODE key.

Each press switches the setting as follows:

1 "F-AUTO": Auto detect

("AUTO DETECT" indicator lights up)

2 "D-MANUAL": Fixed to digital input

("DIGITAL" indicator lights up)

3 "ANALOG": Fixed to analog input

("AUTO DETECT", "DIGITAL" indicator goes off)

Can not be selected for DTS playback.

Auto detect:

In "F-AUTO (FULL AUTO)" mode ("AUTO DETECT" indicator light

up), the receiver detects the digital or analog input signals

automatically. The receiver will select the input mode and listen-

ing mode automatically during playback to match the type of input

signal (Dolby Digital, PCM, DTS) and the speaker setting. º

The "DIGITAL" indicator lights up when a digital signal is detected.

The "DIGITAL" indicator is extinguished when no digital signal is

detected.

Fixed to digital input:

Select this mode if you want to keep the decoding condition

(Dolby Digital, DTS, PCM, etc.) in the current listen mode.

When "D-MANUAL (DIGITAL MANUAL)" mode is selected, the

set listen modes may be changed automatically depending on the

input signal. º

Fixed to analog input:

Select this setting to play analog signals from a VCR, etc.

If the INPUT MODE key is pressed quickly, sound may not be

produced. Press the INPUT MODE key again.

Microcomputer malfunction

If operation is not possible or an erroneous display appears, even

though all connections have been made properly, reset the micro

computer referring to "In case of difficulty". ﬁ

Notes

1. Be sure to turn off the system components before connecting them.

2. Be sure to insert every connection cable completely into the jack.

Incomplete connection may result in absence of audio output or

production of noise.

3. Be sure to disconnect the power cord from the AC wall outlet before

inserting or removing a connection cable.

4. Installation of outdoor antenna is a dangerous work. Please have your

dealer or a specialized technician install it.

Analog audio connections

Audio connections are made using RCA pin cords. These cables transfer

stereo audio signal in an "analog" form. This means the audio signal

corresponds to the actual audio of two channels. These cables usually

have 2 plugs on each end, one red for the right channel and one white for

the left channel.

These cables are to be prepared separately by the user.

Be sure to adhere to the following, or proper ventilation will be

blocked causing damage or fire hazard.

÷ Do not place any objects impairing heat radiation onto the top of

the unit.

÷ Leave some space around the unit (from the largest outside

dimension including projection) equal to or greater than, shown

below.

Top panel : 10 cm (3-15/16")

Side panel : 10 cm (3-15/16")

Back panel : 10 cm (3-15/16")

÷ Do not use the appliance on a bed, sofa, rug or similar surface.

Otherwise, absorption of dust may cause a fire hazard.

CAUTION

Make sure that the power cord plug is disconnected from the AC wall

outlet before proceeding to connections. Also be sure to disconnect the

power cord plug from the AC wall outlet before changing connections.

For the connections of other system components, see pages 8 to 13.

When connecting an associated system component, be sure to read

its instruction manual.

Input selector keys

CAUTION

The power in this equipment will not be completely cut off from the wall

outlet when the power switch is turned off.

Install the equipment so that the wall outlet is easily accessible and, in

case of emergency, immediately unplug the power cord from the wall

outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood VRS6200 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kenwood VRS6200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info