Bedienungsanleitung Kenwood ZJM810 Mesmerine (Seite 4 von 109) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

706677

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

English

before plugging in

Make sure your electricity supply is

the same as the one shown on the

underside of your kettle.

WARNING: THIS APPLIANCE

MUST BE EARTHED.

l

This appliance conforms to EC

Regulation 1935/2004 on materials

and articles intended to come into

contact with food.

before using for the first

time

1 Wrap any excess cord around the

bracket

e on the underside of the

powerbase.

2 Fill to ‘MAX’, boil, then pour the

water away. Repeat 3 times.

key

a lid

b on/off switch

c 360° powerbase

d power on light

e cord wrap

f filter

A water level gauge

to use your kettle

1 Fill the kettle by removing the lid.

The water level must be between

‘MAX’ and ‘MIN’ (250mls) on the

water level gauge inside the kettle

(A).

If you live in a hard water area we

recommend that you use filtered

water in order to maintain the

appearance and efficiency of your

kettle.

Be economical: do not boil more

water than you need.

To improve the quality of your

drinks always use fresh water.

Empty the kettle after each use.

Rinse out with fresh water if the

kettle has not been used for more

than 2 days.

2 Check the lid is fitted correctly.

3 Plug in and switch on. The power

on light

d will come on.

4 Your kettle will boil and switch off

automatically. To re-boil, wait a few

seconds - the on/off switch needs

time to reset.

Note - To interrupt the

boiling ensure that the

switch is in the off position

before removing from the

powerbase.

If you experience problems

with your kettle switching

on and off during use or

switching off before boiling,

check that the flat element

is free from scale - see

“descaling”.

Your kettle is fitted with a filter to

hold back limescale particles.

If you find drops of water under

your kettle, do not worry - it is just

condensation.

boil-dry protection

If you switch on with too little

water, your kettle will cut out

automatically. Switch off, remove

from the powerbase and let it cool

down before re-filling. When it has

cooled down, the switch will reset

itself.

care and cleaning

Before cleaning, unplug your kettle

and let it cool down.

the outside and powerbase

Wipe with a damp cloth, then

dry. Do not use abrasives - they

will scratch the metal and plastic

surfaces.

the inside

Wipe with bicarbonate of soda on

a damp cloth. Rinse thoroughly.

Even though your kettle comes

with a filter, you still need to clean

the inside (and the filter) regularly.

the filter (B+C)

1 Remove the lid.

2 Lift the filter out away from the

spout area (B).

3 either rinse under the tap or use

a soft brush or when descaling

your kettle, drop the filter in too.

Rinse thoroughly.

4 Place the filter back in the spout

area and push down to secure (C).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kenwood ZJM810 Mesmerine Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info