Bedienungsanleitung Ketron Audya series (Seite 33 von 204) (Englisch)

677862

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

KETRON • AUDYA 33

Wave Sync

Figure 40

Figure 41

Figure 42

NOTE

1) No limitations to add same audio track on different

points of MIDI file.

2) User can assign just one single Wave at a time.

3) If a Wave have the parameter Repeat set into Loop

mode (before the value 1) then all the others Waves

associates to the MIDI file having a subsequent Start

bar will be ignored.

Wave Sync

WAVE SYNC Environment allows to assign several

wave tracks synchronized to MIDI track by MIDI

clock. On this feature you can assign Starting /Stop /

Repeat measure for each Wave track assigned.

1. WAVE and MIDI tracks must be located on the

same folder.

2. Use F8 button to select WAVE SYNC feature .This

action allows to Create or Edit your WAVE SYNC

files.

3. Enter into the MIDI player and select the MIDI file

to be edit and press Load MIDI (F10). Display will

show a loading pop-up message. Once loading

procedure will be completed PLAY and STOP

function will be available on F10 button to listen

the MIDI file. This function is also replicated by

the Start button on Main layout (Figure 40).

4. Now add your own Wave on MIDI file. Use panel

arrows to navigate on desiderated Waves and

then press ADD LOOP (F8) button to assign

(Figure 41).

5. Once Wave Loop will be assigned Audya’s

display will show info and properties related to

this file:

• F1 - Wav: This value show the Wave’s progressive

number.

• F2 - Name: name of selected Wave.

• F3 - Bpm: Beat per minute of selected Wave in

case on a Drum Loop. This basically info will be

used to sync your Audio file onto the MIDI clock.

Correct BPM information is essential to define the

best synchronization between Audio and MIDI.

The BPM value can be modified also when Audio

and MIDI are playing.

• F4 – Start: Start information for the Wave file.

User can define just only Audio Start bar as the

Stop bar will be defined automatically according

to Length and Repeat parameters.

• F5 - Length: Length on bars for the Wave.

This value will define the right length for the

Wave performance. Pay attention when set this

parameter to obtain the correct playing and stop

point for your audio track..

• F6 - Repeat: This function select the number of

repetitions for the Wave. When set to the Loop

value (before the number 1) the Audio track will

be repeated from it’s initial Start bar until the end

of the MIDI file.

• F7 - Remove Wav: allows to remove the selected

Wave.

• F8- Add Wav: this command permit to add the

Wav to the MIDI file.

• F9 - Play Wav: allow to Play the selected Wave

(Figure 42).

6. Once all parameters are set properly the user

can arrange a sort of preview of the final project

simply by playing the MIDI file (F10).

7. In order to save the new MIDI + Audio

combination it’s enough to press SAVE on the

panel. Give a new name and confirm again with

the button 5 / 10 – Save.

8. The playback is obtained by selecting the new

MIDI file and starting with Enter. The Wave volume

may be adjusted separately from MIDI by the

slider Wave.

9. In order to add other tracks repeat carefully point

from #5 to #7 .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ketron Audya series Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ketron Audya series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info