Bedienungsanleitung Kettler BOSCH Intuvia Pedelec 2021 (Seite 88 von 118) (Englisch)

773009

Zoom out

Zoom in

Vorherige Seite

1/118

Nächste Seite

MY21K01 - 12_1.0_05.08.2020 88

Troubleshooting, fault clearance and repair

9.1.7 Other errors

9.2 Repair

Special knowledge and tools are required for

many repairs. That is why only a specialist dealer

may perform repairs such as:

• Replacing tyres and rims

• Replacing rims and brake linings or brake discs

• Replacing and tensioning the chain.

9.2.1 Original parts and lubricants

The individual pedelec parts have been carefully

selected and matched to one other.

Only original parts and lubricants must be used for

maintenance and repair.

The constantly updated accessory approval and

parts lists are in Section 11 Documents and

Drawings.

Observe the operating instructions for the new

components.

9.2.2 Replacing the lighting

Only use components of the respective power

class for replacement.

9.2.3 Adjusting the headlight

The headlight must be set, so that its light beam

shines on the road 10 m in front of the pedelec.

9.2.4 Tyre clearance check

The tyre needs to be checked each time a

suspension fork tyre is changed to another size.

1Release pressure from the fork.

2Press fork together fully.

3Measure the gap between the top of the tyre

and the crown's lower surface. The gap must

not be less than 10 mm. If the tyre is too large,

the tyre will touch the crown's lower surface if

the fork is fully pressed together.

4Release pressure on fork and pump it up again

if it is an air suspension fork.

5Take into account the fact that the gap will be

smaller if there is a guard. Check again to

ensure that there is sufficient clearance for the

tyre.

Symptom Cause Remedy

Two beeps will sound if a

switch is pressed but the

switch cannot be

operated.

Pressed switch mode has been

deactivated.

This is not a malfunction.

Three beeps are

sounded. A fault or warning has occurred.

This occurs when a warning or an error is shown on the

display screen. Follow the instructions for the code indicated

on screen in Section 6.2 System Messages.

When you use an

electronic gear shift, you

can feel that pedal

assistance becomes

weaker when the gear is

changed.

This is because the computer sets the

pedal assistance to the optimum level.

This is not a malfunction.

A noise can be heard

after switching.

Contact your specialist dealer.

It is normal to hear a

noise coming from the

rear wheel when cycling

as normal.

The gear shift setting may not have

been made properly.

Contact your specialist dealer.

If you stop the pedelec,

gear transmission does

not switch to the position

pre-configured in the

functional feature.

You may have applied too much

pressure onto the pedals.

It is easier to change gears if you press onto the pedals gently.

Table 54: Error solution for battery

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kettler BOSCH Intuvia Pedelec 2021 Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kettler BOSCH Intuvia Pedelec 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info