Bedienungsanleitung Kettler Traveller - 2020 (Seite 39 von 125) (Englisch)

773015

Zoom out

Zoom in

Vorherige Seite

1/125

Nächste Seite

MY20K01-12_1.0_12.06.2019 39

Overview

Applies only to Pedelecs with eShift with NuVinci

H|Sync/ enviolo with Optimized H|Sync

Applies only to Pedelecs with eShift with Rohloff

E-14 Speedhub 500/14

3.5.5 System message

The drive system monitors itself continuously and

if an error is detected, it is indicated by a system

message. The system may switch off

automatically depending on the type of error. You

will find assistance for system messages in 8.5

First aid. There is a table of system messages in

the Appendix.

3.5.6 ABS indicator lamp

The anti-blocking system indicator lamp must light

up after the system has started up and must go

out once speed has reached about 5 km/h. If the

ABS indicator lamp does not light up when the

electric drive system starts, the ABS is defective.

An error code on the display also tells the rider

that it is defective.

If the indicator lamp does not go out after you set

off or it lights up while you are riding, this means

there is an error in the anti-blocking system. The

anti-blocking system is then no longer active. The

brake system itself remains functional. It is only

the anti-blocking system control which no longer

operates.

If the ABS indicator lamp is lit, the ABS function is

not active.

Note: You need to stop and restart the pedelec

(switch off and on again) to reactivate the anti-

blocking system.

Screen display Change

Gear calibration This is where you can perform a

calibration on the stepless gear.

Press on the Lighting button to

confirm calibration. Then follow the

instructions. You also might need

to perform a calibration while riding

in the event of a fault. In such

cases, you also press on the

Lighting button to confirm

calibration and then follow the

instructions on the display. This

menu option is only shown when

the on-board computer is

positioned in its mount

Gear vx.x.x.x: this is the gear software version.

This menu option is only shown

when the on-board computer is

positioned in its mount. This menu

option is only shown if you have an

electronic control gear.

Table 45: Changing the system settings

Screen display Change

Start gear This is where you can set the start

gear.

The automatic reset function is

switched off in Position – –. This

menu option is only shown when

the on-board computer is

positioned in its mount.

Gear vx.x.x.x: this is the gear software version.

This menu option is only shown

when the on-board computer is

positioned in its mount. This menu

option is only shown if you have an

electronic control gear.

Table 46: Changing the system settings

Notice

The anti-blocking system indicator lamp may light

up if the front and rear wheels are rotating at

widely different speeds from one another – for

example, if the rider cycles on the rear wheel only

or if a wheel is rotating for a unusually long time

without making contact with the ground (fitting

stand). The anti-blocking system switches off in

such cases.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Kettler Traveller - 2020 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Kettler Traveller - 2020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info