773015
51
Zoom out
Zoom in
Vorherige Seite
1/125
Nächste Seite
MY20K01-12_1.0_12.06.2019 51
Assembly
5.3.4.2 Adjusting the FOX quick release
Figure 46: Structure of quick release from rear with (1)
axle nut lock, (2) axle nut securing screw, (3) directional
arrow, (4) axle setting value and (5) axle nut
Record the axle setting value (4) indicated by
the directional arrow (3).
Loosen the axle nut securing screw (2) with a
2.5 mm hex key by approx. four revolutions,
but do not remove the screw completely.
Turn the quick release lever to the open
position and loosen the axle by approx. four
revolutions.
Press the axle inward from the side of the open
lever. This pushes out the axle nut securing
screw so that you can turn it out of the way.
Push the axle further forward and turn the axle
nut clockwise to increase the lever tension or
anti-clockwise to reduce the lever tension.
Reinsert the axle nut lock and tighten the screw
to 0.9 Nm (8 in-lb).
Repeat the steps for installing the axle to check
proper installation and correct adjustment.
5.3.4.3 Mounting the wheel with Kabolt axles
The procedure for installing the 15 x 100 mm and
15 x 110 mm Kabolt axles is the same.
Place the front wheel in the fork ends of the
fork. Push the Kabolt axle through the fork end
on the non-drive side and hub.
Figure 47: Pushing the Kabolt axle in
Tighten the Kabolt axle screw to 17 Nm
(150 in-lb) with a 6 mm hex key.
5.3.4.4 Checking the stem and handlebars
Checking connections
Stand in front of the pedelec to check whether
the handlebars, stem and fork steerer are
firmly attached to one another. Clamp the front
wheel between your legs. Grasp the handlebar
grips. Try to twist the handlebars towards the
front wheel.
The stem must not move or twist.
Firm hold
Place your entire body weight on the
handlebars with the quick release lever closed
to check that the stem is firmly in place.
The handlebars shaft must not move
downwards in the fork steerer.
If the handlebars shaft should move in the fork
steerer, increase the quick release lever
tensioning. To do so, turn the knurled nut
slightly in a clockwise direction with the quick
release lever open.
Close the lever and check the stem is firmly in
position.
1
2
3
45
51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Kettler Traveller - 2020 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Kettler Traveller - 2020

Kettler Traveller - 2020 Bedienungsanleitung - Deutsch - 125 seiten

Kettler Traveller - 2020 Bedienungsanleitung - Holländisch - 128 seiten

Kettler Traveller - 2020 Bedienungsanleitung - Französisch - 131 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info